Comnet CNGE2FE8MSPOE2 Скачать руководство пользователя страница 50

Страница: 50 / 105

INS_CNGE2FE8MSPOE2_REV–

12/20/12 PAGE 50

INSTALLATION AND OPERATION MANUAL

CNGE2FE8MSPOE2

TECH SUPPORT: 1.888.678.9427

VLAN Configuration – 802.1Q interface

Label

Description

VLAN Operation Mode Select VLAN Operation Mode: Disable, Port Base, 802.1Q
GVRP Mode

Enable/Disable GVRP function.

Management VLAN ID Management VLAN can provide network administrator a

secure VLAN to management Switch. Only the devices in the
management VLAN can access the switch.

Port

Select the port to configure.

Link type

Select Link Type from the following options:

Access Link

: Single switch only, allows grouping of ports

by setting the same VID.

Trunk Link:

Extended application of Access Link, allows

grouping of ports by setting the same VID
with 2 or more switches.

Hybrid Link:

Both Access Link and Trunk Link are

available.

Hybrid(QinQ) Link:

Allows one more VLAN tag in a original

VLAN frame.

Untagged VID

Set the port default VLAN ID for untagged devices that connect
to the port. The range is 1 to 4094.

Tagged VIDs

Set the tagged VIDs to carry different VLAN frames to other switch.

Apply

Select

Apply

to activate the configurations.

Содержание CNGE2FE8MSPOE2










































































































Результаты поиска

Содержание CNGE2FE8MSPOE2

Отзывы:

Comnet CNGE2FE8MSPOE2, Инструкция по установке и эксплуатации, Страница: 50 / 105

Результаты поиска

Содержание CNGE2FE8MSPOE2

Отзывы: