Comnet CNGE2FE8MSPOE2 Скачать руководство пользователя страница 14

Страница: 14 / 105

INS_CNGE2FE8MSPOE2_REV–

12/20/12 PAGE 14

INSTALLATION AND OPERATION MANUAL

CNGE2FE8MSPOE2

TECH SUPPORT: 1.888.678.9427

CNGE2FE8MSPOE2

1. LED for PWR. When the PWR links, the green LED will be light on.

2. LED for PWR1. When the PWR1 links, the green LED will be light on.

3. LED for PWR2. When the PWR2 links, the green LED will be light on.

4. LED for R.M (Ring master). When the LED light is on, this switch is the C-Ring ring master.

5. LED for Ring. When the LED light on, it means the C-Ring is activated.

6. LED for Fault Relay. When the fault occurs, the amber LED will be light on.

7. Console port (RJ-45).

8. LED for PoE power supplied.

9. 10/100BASE-T(X) PSE Ethernet ports.

10. LED for Ethernet ports speed.

11. LED for Ethernet ports link status.

12. Gigabit COMBO ports with SFP

13. LED for SFP ports link/Act status.

Содержание CNGE2FE8MSPOE2










































































































Результаты поиска

Содержание CNGE2FE8MSPOE2

Отзывы:

Похожие инструкции для CNGE2FE8MSPOE2

Бренды по названию

Популярные бренды

Comnet CNGE2FE8MSPOE2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CNGE2FE8MSPOE2

Отзывы:

Похожие инструкции для CNGE2FE8MSPOE2

Бренды по названию

Популярные бренды