commercial cool CTE08A Скачать руководство пользователя страница 14

14

The outside temperature is below 66°F (19°C). 

Do not try to 

operate your air conditioner in the cooling mode when the 
outside temperature is below 66°F (19°C).

The temperature of the room you are trying to cool is 
extremely hot. 

Allow extra time for the air conditioner to cool 

off a very hot room.

Windows or doors to the outside are open. 

Close all 

windows and doors.

The Air Exchanger is set to OPEN (on some models).

 Set 

the Exhaust control to CLOSED for maximum cooling and/or 
heating.

Temperature control is not at a cool enough setting. 

Adjust the Temperature control to a cooler setting. Press the 
TEMP minus pad to reduce the temperature by 1º until it 
reaches 66ºF (19ºC). Set the Fan Speed control to High or 
Turbo (on some models).

Water drips from cabinet into your house

The air conditioner is not properly leveled.

 The air 

conditioner should slope slightly downward toward the 
outside. Level the air conditioner to provide a downward 
slope toward the outside to ensure proper drainage. See the 
Installation Instructions. 

NOTE:

 Do not drill a hole in the bottom of the metal base and 

condensate pan.

Air conditioner cooling, but room is too warm—Ice 
forming on cooling coil behind intake grille

The outside temperature is below 66°F (19°C). 

Do not try to 

operate your air conditioner in the cooling mode when the 
outside temperature is below 66°F (19°C).

The filter is dirty or obstructed by debris. 

Clean the filter. 

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check 
“Troubleshooting.” It may save you the cost of a service call. If 
you still need help, follow the instructions below. 

When calling, please know the purchase date and the complete 
model and serial number of your appliance. This information will 
help us to better respond to your request.

If You Need Replacement Parts

If you need to order replacement parts, we recommend that you 
only use factory specified replacement parts. Factory specified 
replacement parts will fit right and work right because they are 
made with the same precision used to build every new appliance.

To locate factory specified replacement parts in your area, call us 
or your nearest designated service center.

Keep this book and your sales slip together for future 
reference. You must provide proof of purchase or installation 
date for in-warranty service.

Write down the following information about your major appliance 
to better help you obtain assistance or service if you ever need it. 
You will need to know your complete model number and serial 
number. You can find this information on the model and serial 
number label located on the product.

Dealer name____________________________________________________

Address ________________________________________________________

Phone number __________________________________________________

Model number __________________________________________________

In the U.S.A.

Call Haier America toll free: 

1-877-337-3639.

Our consultants provide assistance with:

Features and specifications on our appliances.

Installation information.

Use and maintenance procedures.

Repair parts sales.

Referrals to repair parts distributors, and service companies. 
Manufacturer-authorized service technicians are trained to 
fulfill the product warranty and provide after-warranty service, 
anywhere in the United States.

For Further Assistance

If you need further assistance, you can write with any questions 
or concerns to:

Haier America
1356 Broadway
New York, NY 10018

Please include a daytime phone number in your correspondence.

In Canada

Call Haier America toll free: 

1-877-337-3639.

Our consultants provide assistance with:

Features and specifications on our appliances.

Use and maintenance procedures.

Repair parts sales.

Referrals to repair parts distributors, and service companies. 
Manufacturer-authorized service technicians are trained to 
fulfill the product warranty and provide after-warranty service, 
anywhere in Canada.

For Further Assistance

If you need further assistance, you can write with any questions 
or concerns to:

Haier America
1356 Broadway
New York, NY 10018
U.S.A.

Please include a daytime phone number in your correspondence.

Содержание CTE08A

































Отзывы: