background image

APR/16/2002 

6979 USA 

15

   

 

 

 

TX780V  

TWO-WAY LCD SCREEN REMOTE TRANSMITTER

 

 

B. FEATURES PROGRAMMING: 

 

ALARM FEATURE “

I

” PRORAMMING:   

1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.   
2. Push the Valet switch 

2

 times and hold it until 

one

 chirp with a long chirp is hearing then release the valet 

switch. You are now in the Alarm feature 

‘I’

 programming mode. 

3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.   

a.

 

The siren chirps and LED pause will indicate previously setting. 

b.

 

The factory default settings is always [1] LED flash, [1] chirp. 

4  Depress the transmitter button ‘A’ again to change the feature. Simple keep re-depressing the transmitter 

button ‘A’ again until the module advances to your desired setting. 

a.

 

In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirps. 

b.

 

Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc. 

5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program. 

For example: 

To program the arming mode form “Active arming” to “Passive Arming without Passive Door 

Locking”, After “Arming mode” program, the next program is “Rearm on/off” .………. 
1  Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.   
2  Push the Valet switch 2 times and hold it until a chirp with a long chirp is hearing then release the valet 

switch. 

3  Press and release the transmitter 

 

button corresponding to the feature ‘Arming mode’ you wants to 

program. [1] LED flash, [1] chirp to indicate your are in features “Active Arming”. 

4  Depress the transmitter  

button twice to change the feature. [3] LED flash, [3] chirps to indicate your 

are in features “Passive Arming without Passive Door Locking ”. 

5 Depress  the  transmitter 

 

button corresponding to the features ”Rearm on/off”’ you want to 

program…….. 

 

Press 
Transmitter 
Button 

One Chirp /   
LED one pulse 

Factory Default 
Setting

 

Two Chirps / 
LED two pulse 

 

Three Chirps / 
LED three pulse 
 

Four Chirps / 
LED four pulse   
 

 

All chirps on 

Siren chirp on only 

Horn chirp on only 

All chirps off 

 

Active arming 

Active arming with 
Passive starter 
disable  

Passive arming 
without passive door 
locking 

Passive arming with 
passive door 
locking. 

 

Automatic Rearm on  Automatic Rearm off   

 

 

With Door Ajar error 
chirp 

Bypass Door Ajar 
error chirp. 

 

 

 

Without Car-jack 
mode 

Active Car-jack 
mode  

Passive Car-jack 
mode 

 

 

 

Transmitter can not 
Arm the System 
When Driving 

Transmitter can be 
Arming the System 
When Driving 

 

 

 

 

 

Panic with Ignition 
off 

Panic with Ignition 
on & off 

Panic with Ignition 
on & off.    Panic with 
No time limit. 

Without Panic 
function. 

 

Содержание FM-760


























Отзывы: