background image

7

REMOTE START FEATURES

TRANSMITTER FUNCTIONS

4

ENGINE RPM PROGRAMMING

Select Engine Start RPM detection - step 20 in the programming table.

With engine running select step 21 in the programming table

, note that the LED is

blinking, indicating that the RPM signal is detected properly, 

press button 1 on your

remote control to record the idle RPM.

ENGINE RUN DETECTION

There are two modes of engine run detection

RPM –

 Engine run sensing is accomplished by supplying an RPM signal to the unit and

teaching the “vehicle engine idle RPM”. Engine stalled condition is defined as zero
engine RPM.

Smart Sense –

 Engine run is determined by measuring the battery voltage and engine noise.

Engine stalled condition is defined if both the battery voltage and engine noise have been
fallen bellow a per-determined threshold.

ENGINE START DETECTION

Engine start is detected only when using the RPM mode, in this mode RPM timing is compared
to pre programmed idle RPM, engine start is defined as 50% of idle RPM. If engine RPM did
not reach that level within 10 seconds, engine cranking will be terminated.
If Smart Sense is selected engine start is controlled by timing only.

DIESEL/GASOLINE MODE

Gasoline mode -

 Ignition is turned On 5 seconds before start.

Diesel Mode -

 Ignition is turned On 10 seconds before start or until the Glow plug is turned

Off whichever comes first.

COLD START

Cold Start is programmable to every 2 or 1 hour intervals.
Enable Cold Start – with Ignition Off simultaneously press the brake pedal Valet switch and
button 1 on your remote - Parking lights will flash twice confirming that the feature has been
enabled.

* This feature will be canceled if the alarm has been armed and disarmed or
ignition has been turned On.

STOP & GO MODE

With engine running press remote start button on your transmitter, sidelights will flash twice
indicating STOP & GO mode enabled, turn off the Ignition switch, the engine will continue
running.

TRANSMITTER FUNCTIONS WITH DEFAULT SETTINGS

Button # 1 upper left button  (arm with chirps and press 3 seconds for panic)
Button # 2 upper right button (disarm with chirps and press one more time for passenger unlock)
Button # 3 lower left button   (press for 2 seconds for trunk release, aux 1)
Button # 4 lower right button  (press for remote start)
Button # 5 Side right button    (function button)

Transmitter functions with function button pressed once (with default settings)

Button # 1 upper left button  (arm without chirps)
Button # 2 upper right button (disarm without chirps and press one more time for passenger unlock)
Button # 3 lower left button   (press for aux 2)
Button # 4 lower right button  (not used)

Transmitter functions with function button pressed two times (with default settings)

Button # 1 upper left button  (arm with chirps, second car operation)
Button # 2 upper right button (disarm with chirps and press one more time for passenger unlock,
second car operation)
Button # 3 lower left button   (trunk release, second car operation)
Button # 4 lower right button  (remote start, second car operation)

Transmitter functions with function button pressed three times (with default settings)

Button # 1 upper left button  (not used)
Button # 2 upper right button (not used)
Button # 3 lower left button   (sensor adjust & test mode)
Button # 4 lower right button  (not used)

BUTTON #1

LOCK
ARM

BUTTON #2

UNLOCK
 DISARM

BUTTON #3

 Hold 3 Sec.
 For TRUNK

BUTTON #4

REMOTE
  START

BUTTON #5 (function)

E

Press Momentary Will
Shift to Next Bank.

Remote Operation In Bank #1

#5 +1= 

Silent Arm

#5 +2= 

Silent Disarm

#5 +3= 

4 Th. Channel

#5 +4= 

Shock sensor disable

3 4

1

2

Remote Operation In Bank #2

LOW BATTERY INDICATOR :

The Pager will indicate when it is time to replace the battery by lighting the
BATTERY symbol. This indication is not for the pager. But rater the remote transmitter. Audible
paging "beeps" will become none audible before battery replacement is necessary for the remote
transmitter.

REPLACING THE BATTERY :

Remove battery cover. And Remove old battery.
Replace with 1.5V AAA Battery

Two Way Remote

2

4

1

3

Notes

+

BATTERY

Back of the Remote

cover lock

Отзывы: