2
9
V
TRANSMITTER BUTTON OPERATION
IMPORTANT:
The microprocessor alarm system has been designed so that upon arming,
Sensor 1 & 2 triggers will be delayed for 10 seconds. This is to give the electronics in the
vehicle, a chance to stabilize (Window roll-up, shock sensor, etc.).
ACTIVE ARMING MODE
Press transmitter button #1 momentarily to arm the alarm system. The alarm will arm and the
siren will chirp once, sidelights will blink, doors will lock automatically, optional starter disable
feature will be activated and the LED will turn on solid then begin flashing slowly after a 10
second delay.
DISARMING THE SYSTEM
Press transmitter button #2 momentarily to disarm the alarm system. The alarm will arm and
the siren will chirp twice, sidelights will flash twice LED will turn off Optional starter disable
feature will be deactivated Door locks will unlock automatically Dome light will be illuminated
for 30 seconds or until ignition key is turned to accessory “ON” position.
ARMING WITH TRANSMITTER (NO CHIRP)
Press transmitter button #5 momentarily. Then press button #1 the alarm will arm silently (no
siren chirps).
DISARMING WITH TRANSMITTER (NO CHIRP)
Press transmitter button #5 momentarily. Then press button #2 the alarm will disarm silently
(no siren chirps).
PASSIVE ARMING MODE
In passive arming mode, upon closing the last door there will be a 30 second arming delay. The
LED will be flashing rapidly and 5 seconds later parking light will flash two times indicating that
the system is in passive arming phase. After 30 seconds, the alarm will arm (Programmable).
ONE TIME PASSIVE ARMING DISABLE
Arm and disarm the alarm within 10 seconds, this will disable passive arming until you either
turn the ignition on, or arm the alarm and wait 10 seconds then disarm.
ARMING WITH DEFECTIVE ZONE ALERT
After arming the alarm (active or passive) .if a defective zone has been detected. The alarm will
confirm the detection of the defective zone by chirping the siren and flashing the lights 4
times. Also will identify the defective zone with LED. All defective zones will be bypassed until
they become good then the alarm will start monitoring them except both sensor once bypassed
they stay bypassed until you disarm and arm the unit.
PANIC MODE
For emergency situations, press and hold button #1, of the transmitter for 3 seconds. This will
activate the panic mode. The alarm siren will sound, armed output will be active, doors will
unlock and the parking lights will flash for 30 seconds (or until the transmitter button #2 is
pressed. (If ignition is on while panicking the doors will lock.
ALARM TRIGGERED
If a violation of the vehicle is taking place, the siren will sound, horn will flash, and the parking
lights will flash for 45 seconds. After this 45 seconds duration, the alarm will automatically
reset and resume protecting the vehicle. Sensor 1 sensor 2 triggers will sound the alarm 30
seconds.
PROGRAMMING THE UNIT
FEATURE PROGRAMMING MODE
1-
Turn Ignition key ON
2-
Within 10 seconds press VALET switch 5 times. The siren will chirp 3 times indicating you
are in feature programming mode.
3-
Select the feature you want to change by pressing the valet switch the number of
times as the feature number. (Every time valet switch is pressed the siren will chirp once).
4-
Select the desired option by pressing the transmitter’s buttons 1, 2 or 3.
Siren chirps will follow each button press, once for button 1, twice for button 2 and three
times for button 3.
PARKING LIGHT POLARITY SELECTION:
Remove the plastic cover of the control module and find jumpers W5 and W2 on the PCB.
Select Parking Light Polarity output by connecting the center tap to “+” or “-”of jumper W5.
Prog. Coded Override
Ignition Unlock - Off
Set Starter for Diesel
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
#11
#12
#13
#14
#15
#16
#17
#18
#19
#20
#21
#22
#23
#24
TX But. 1 Mode 1
TX But. 2 Mode 2
TX But. 3 Mode 3
PROGRAMMING TABLE
#s
Passive Arm Disable
Auto Rearm Disable
Chirps Enable
Ignition Lock Enable
Ignition Unlock All doors
Unlock Single Pulse
Lock/Unlock Pulse 1sec.
Lock on Passive Arm Disable
Door Trigger delay disable
Bad door zone report in 5 sec.
Activate Aux.2 upon arm-disable
Aux.1 pulsed
Aux. 2 pulsed
Disarm with Aux. 1 Disable
Starter in Valet Disable
Door lock Upon Starter
Door lock after Shutdown
Run Time 12 Min
Cold Start Every 2 hours
Smart Start Enable
Learn RPM threshold
Adding 2 way FM Module
Aux. Relay Out for Ignition-2
Aux 3- Horn Out
Passive Arm Enable
Auto Rearm Enable
Chirps Disable
Ignition Lock Disable
Ignition Unlock – Driver door
Unlock Double Pulse
Lock/Unlock Pulse 3sec
Lock on Passive Arm Enable
Door trigger delay Enable
Disable bad door zone report
Activate Aux.2 upon arm-Enable
Aux.1 Timed
Aux. 2 Timed
Disarm with Aux. 1 Enable
Starter in Valet Enable
No Door lock Upon Starter
No Door lock after Shutdown
Run Time 24 Min
Cold Start Every 1 hour
RPM Start Enable
Set starter for Gasoline Vehicle
Program 2-way FM remote
Aux. Relay Out for Accessory-2
Aux 3- Ignition Out
Aux. 1 Latched
Aux. 2 Latched
Aux. Relay Out for
Starter-2
RESET TO FACTORY DEFAULT SETTING:
ENTER PROGRAM MODE (SEE ABOVE)
PRESS AND HOLD CHANNEL 3 (OR BUTTON #3 ) FOR 5 SECONDS LIGHT WILL FLASH 3
TIMES .AND ALL PROGRAMMABLE FEATURES WILL GO BACK TO FACTORY DEFAULT
SETTINGS.
(
WHICH IS ALL MODE 1
)
Column 1 - Factory Default
t
