Comfort Glow Brentwood LCF18 Скачать руководство пользователя страница 13

Страница: 13 / 20

www.desatech.com

115043-01D

TROUBLESHOOTING

WARNING: Turn off log set and let cool before servicing. Only a

qualified service person should service and repair log set.

Note:

All troubleshooting items are listed in order of operation.

POSSIBLE CAUSE

1. Poor fuel quality

2. Fireplace venting system not

drafting properly

3. Excessive flame impingement

or blockage

4. Improper fuel/air mixture

5. Excessive gas supply/pres-

sure

1. Passage of air/gas across ir-

regular surfaces

1. Incorrect gas supply or

pressure

2. Blocked burner orifice or

burner manifold ports

3. Improper burner orifice size

1. Ignitor electrode not con-

nected to ignitor cable

2. Ignitor cable pinched or wet

3. Bad ground on piezo ignitor

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode positioned

wrong

OBSERVED PROBLEM

Log set is smoking/sooting ex-

cessively (

Note:

It is natural and

unavoidable for vented gas log

sets to produce moderate levels

of carbon (soot) where flames

contact the logs.

Burner is excessively noisy

(

Note:

The movement and com-

bustion of gas will create low,

unavoidable levels of noise.)

Burner flame is too low or too

high

When ignitor button is pressed,

there is no spark at pilot

(GA9050A Only)

REMEDY

1. Contact local natural or pro-

pane/LP gas company

2. Adjust damper wide open and/or

have fireplace and venting pro-

fessionally cleaned and checked

3. Separate the logs to allow more

flame passage

4. Remove any foreign items from

the flame pattern and/or check

for proper orifice sizing

5. Preheat flue in very cold

weather

1. Relieve any tight bends or

kinks in gas supply line

1. Check for proper gas supply

pressure

2. Free burner orifice and mani-

fold ports of any burrs, paint,

or other blockage

3. Verify proper burner orifice

sizing (see Figure 2, page 6)

1. Reconnect ignitor cable

2. Free ignitor cable if pinched

by any metal or tubing. Keep

ignitor cable dry

3. Scrape away paint on bracket

for better contact with ground

on piezo ignitor

4. Replace ignitor cable

5. Replace piezo ignitor

6. Replace electrode

7. Reposition electrode

Содержание Brentwood LCF18





















Результаты поиска

Содержание Brentwood LCF18

Отзывы:

Бренды по названию

Популярные бренды

Comfort Glow Brentwood LCF18, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание Brentwood LCF18

Отзывы:

Бренды по названию

Популярные бренды