COMFORT-AIRE AMC 25 Скачать руководство пользователя | Manualshive

Страница: 5 / 24

background image

MOUNTING INSTALLATION PLATE:

The fan coil can be installed using any of the four methods described below.
Determine which is the most suitable method.

Position the installation plate on the wall
making sure that it is parallel to the ground.
This can be done by aligning the marking-
off line with a thread and weight as shown
in figure on the right. This is to ensure that
the condensate water does not overflow
from the drain pan.

Mount the installation plate with the 4
screws provided. (If the unit is to be
mounted on a concrete wall, consider using
anchor bolts instead of the screws provided.

«
...
3
4
5
6
7
...
»

Содержание AMC 25

























Отзывы:

Нет отзывов

Похожие инструкции для AMC 25

MCM-A200 User Manual (XP)

Бренд: Samsung Страницы: 12

AERAMAX PRO AM3 PC

Бренд: Fellowes Страницы: 8

Бренд: Quasar Страницы: 24

Бренд: Quasar Страницы: 24

Бренд: Quasar Страницы: 20

Бренд: RS Страницы: 12

MTA8F128R5I Series

Бренд: Technibel Climatisation Страницы: 47

Бренд: Sunbeam Страницы: 5

C*ED060A Series

Бренд: Unitary products group Страницы: 24

Бренд: koppel Страницы: 56

Viroxid HABITAT 3 AIR 160

Бренд: IDS Страницы: 28

Бренд: Lennox Страницы: 32

Бренд: Daikin Страницы: 84

Бренд: Rowenta Страницы: 73

Бренд: Yamato Страницы: 68

Бренд: Klimaire Страницы: 11

Бренд: emmeti Страницы: 112

Бренд: AlpicAir Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды