COMFORT-AIRE AMC 25 Скачать руководство пользователя | Manualshive

Страница: 14 / 24

background image

AUXILIARY CONTROL

Figure below illustrates the auxiliary control on the fan coil. This can be used to
operate / control the air conditioner when the remote controller is not available or lost.

Test

Use to operate the air conditioner under "COOL" mode. All other functions will not be
effective. The air conditioner will automatically stop operating after 30 minutes. This is
to test if the air conditioner is in working condition.

Remote

In this position, the air conditioner is controlled by the remote controller.

Auto

Use to by-pass the remote controller. The air conditioner will operate automatically
when power is supplied. The remote controller is ineffective in this position.

Red indicating lamp

Red light will be lit when electrical power is supplied to the air conditioner.

Green indicating lamp

This green lamp will be lit when the compressor starts operating. It indicates cooling
operation is in progress. It will blink if the operating temperature is abnormal.

«
...
12
13
14
15
16
...
»

Содержание AMC 25

























Отзывы:

Нет отзывов

Похожие инструкции для AMC 25

Бренд: Haier Страницы: 52

Бренд: iGenix Страницы: 9

Бренд: Keller Страницы: 2

FHQ100BUV1B x 2

Бренд: Daikin Страницы: 15

Бренд: Soleus Air Страницы: 29

Бренд: Zibro Страницы: 18

Бренд: Timberk Страницы: 56

GWH18AAD-K6DNA1A/I

Бренд: Gree Страницы: 121

Бренд: TATA Motors Страницы: 32

Бренд: MUND CLIMA Страницы: 24

Бренд: GE Страницы: 40

PURE LIGHT UV HTWS026PLUV

Бренд: HTW Страницы: 88

Mini-Floor Console A Series

Бренд: Gree Страницы: 18

Бренд: Daikin Страницы: 501

Бренд: Mitsubishi Heavy Industries Страницы: 88

Бренд: Sanyo Страницы: 2

Бренд: Sanyo Страницы: 2

Бренд: Sanyo Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды