IT
EN
EN
Functions
1. Power LED
2. Connection terminals
| L |
L |
Simplebus2 Data line
| + | - |
Power supply Positive / Negative 12/56 VDC
3. CV5
Jumper for video closure
(Factory setting: closed)
Jumper closed if there is no Simplebus monitor on the line
Jumper open if there are successive Simplebus monitors connected in cascade on the line
4. DIP-Switches
Selectors used to set the Simplebus address
5. DIP-Switches
Selectors used to implement reset procedures
(See “Reset procedures”)
6. Indicator LED
Flashing slowly
Steadily lit
Flashing quickly
System starting up
/ updating
Simplebus line present
System ready
Simplebus line missing
/ short-circuited
7. CV1
(Factory setting: closed)
Jumper open if at least one Simplebus monitor with the same address is on the line
8. LAN port
- Comelit PoE Output - IP address
Factory setting:
DHCP
Only connect to the router or PC using red Comelit cable 1449
9. Indicator LED
Red
Green
Yellow
Steadily lit
Normal operation
Steadily lit
Normal operation
Ethernet connection
present
Flashing
See
"Reset procedures"
Flashing
See
"Reset procedures"
Fig. 1
Technical specifications
Power supply voltage
12 ÷ 56 VDC
Max. absorption (mA)
1100 ÷ 450 (in relation to the power supply voltage)
Max. current delivery
200 mA 12 V
400 mA 48 V
300 mA 24 V
400 mA 56 V
Operating temperature
-5 ÷ 50°C
Operating humidity
5 ÷ 95%
Dimensions
90 x 70 x 59 mm (4 DIN modules)
Art. 20005000 allows monitors and home automation system managers for the ViP system to
be used in Simplebus2 audio/video setups. The ViP monitors/system managers can be used to
receive calls from the external unit and send commands to Simplebus2 devices (self-ignition, call
to main/secondary switchboard, intercom call, actuator control, camera module control, etc.); the
device also offers integration with the SimpleHome home automation system and video entry
phone call forwarding via the Comelit App.
Equipped with 1 Comelit PoE Ethernet port for connection to the ViP monitor and terminals for
connection to the Simplebus2 system.
Art. 20005000 allows use of the Comelit video entry system functions, with the exception of:
Call
divert / Range / Selective intercom / Alarm.
CFP (Floor door call)
: If there are both Simplebus monitors and ViP monitors in the apartment,
connect the CFP to just one Simplebus monitor to receive the call on all monitors.
In relation to the SImplebus2 section of the system, the device should be considered as a separately
powered Simplebus monitor.
ViP monitor addressing
The address of a monitor in a Simplebus system is the address of the apartment preceded by
SBVIP
Examples
Simplebus address
ViP address
Apartment 1
001
SBVIP
001
Apartment 2
029
SBVIP
029
If the ViP monitor keypad does not allow the entry of
alphanumeric
codes, proceed using ViP
Manager software.
Addressing Simplebus devices
To allow the ViP monitor to communicate with Simplebus devices connected to the system,
addresses must be assigned, in the ViP monitor directories, in accordance with the table:
External unit
(Function: Self-ignition)
SBEXT001
Generic actuator
(Function: generic actuator control)
SBACT255
Secondary switchboard
(Function: call to secondary
switchboard)
SBCPS007
Coded actuator xxx
(Function: coded actuator control)
SBACT
xxx
Main switchboard
(Function: call to main switchboard)
SBCPS008
Generic camera module
(Function: generic call module
control)
SBCAM255
Caretaker door-entry phone
(Function: call to caretaker door-entry
phone)
SBCPS009
Addressed camera module xxx
(Function: addressed camera
module control)
SBCAM
xxx
Internal unit
(Function: general intercom call)
SBINT
xxx
Reset procedures
Reboot with predetermined network
settings
Restoring factory settings
This procedure allows you restart the device
with the default network parameter settings,
while keeping the other settings unchanged.
This procedure allows you to restore all the
factory parameter settings and to delete all
the device configurations.
√
DIP-switches in the default positions (OFF)
√
DIP-switches in the default positions (OFF)
1.
Switch off the power supply to the device
1.
Switch off the power supply to the device
2.
Set DIP1 to ON
2.
Set all the DIP-switches to ON
3.
Power on the device
3.
Power on the device
4.
Wait 20-40 sec. until the LEDs start flashing
slowly
and alternately (1 sec. red / 1 sec.
green)
4.
Wait 20-40 sec. until the LEDs start
flashing
rapidly
and alternately (0.1 sec.
red / 0.1 sec. green)
5.
Return the DIP-Switche to OFF
5.
Return all the DIP-Switches to OFF
››
The
green
LED will flash for 5 sec..
››
The device will start with the default network
settings.
6.
At the next restart, the device will recover
the saved settings
.
››
The
red
LED will flash for 5 sec.
››
The device will reset all parameters to the
factory settings and restart in the normal
way.
9
8
