Columbia-Spas Aeware Скачать руководство пользователя страница 22

Страница: 22 / 32

Y Series TechBook

The system has shut down because the temperature at the heater has reached

119°F (48°C).

yes

Take water

temperature

with a digital

thermometer

Is water

temp.

119°F or

higher?

Are you getting

correct water

temperature

reading on

the display?

Is the

weather

very hot?

Verify if

temperature

probe is

properly

connected
If so, replace

heater

Reset system*

yes

Remove spa cover

(even during the night)
Start blower, if spa is

equipped with one

Lower Set Point

below actual water

temperature

Heater

indicator

on keypad display

should disappear

When HL error

message occurs,

does heater

barrel feel

hot? **

Do you get

a 240 V

reading

between

the two

heater

wires on the

board?

Replace

spa pack

Pump is

overheating

water during

filter cycle
Lower filter

cycle duration

Reset system*

Verify if anything

is obstructing water

flow (closed traps

or dirty filters)

Reset system*

Verify if Hi-Limit

probe is properly

connected

Reset system*

If HL error

message persists,

replace spa pack

yes

Wait until spa cools

down (add cold water

if needed)

Reset system*

yes

If problem persists,

replace heater

If problem persists,

replace spa pack

yes

* To Reset System:

Turn power off

and on again at

the main breaker

** Warning! Handle with care as

heater may be really hot!

Water temperature at the
heater has reached 119°F

1 Measure the temper-

ature with a DIGITAL

thermometer and

compare its reading

with temp on the

display Make sure the

temp reading is lower

than 119°F

3 If reading is 119°F or

higher:

• Verify if the Temp &

High Limit probes are

properly connected
• Shut power off and

power the spa up

again to reset the system
• If problem persists,

replace heater
• If problem persists,

replace spa pack

2 If reading is below 119°F:
• Carefully check if

heater barrel feels hot

If it’s hot, verify if anything

is obstructing water flow

(closed valves or dirty

filter)
• Shut power off and

power the spa up again

to reset the system
• If HL error persists,

replace heater
• If HL error persists,

replace spa pack

HL error message / flow chart & step-by-step

Flow chart

Step-by-Step

Regulation probe

Содержание Aeware

































Результаты поиска

Содержание Aeware

Отзывы:

Похожие инструкции для Aeware

Бренды по названию

Популярные бренды

Columbia-Spas Aeware, Руководство пользователя

Результаты поиска

Содержание Aeware

Отзывы:

Похожие инструкции для Aeware

Бренды по названию

Популярные бренды