Collamat 8600 Скачать руководство пользователя страница 37

Страница: 37 / 49

Test drive

The stepper motor of the traction unit and the motor driver can be tested with the

Test

Drive

function. For this test the paper web has to be removed. The speed of the step-

per motor can be increased or reduced with the arrow keys. The test is terminated with
the

ESC

key.

TEST DRIVE

Unload paper

Speed

Start with [ENTER]

Stop with [ESC]

Remote Control

The

Remote Control

function is used to adjust the labeller via the serial interface. This

function is used to set the configuration in the factory. The monitor remains in remote
mode until the menu is abandoned with the

ESC

key. In remote control mode the label-

ler is not operating.

REMOTE CONTROL

Serial Port active
9600 Baud 8 Bits

Working time

The

Working time

function is used to indicate the total operating time of the monitor.

WORKING TIME

Totaly : 25 hrs

Motor running

The

Motor running

function is used to indicate the total feed length of the motor. The

total length is indicated in km.

MOTOR RUNNING

Totaly : 2 km

programmer
STOP

User level:
Operating mode:

programmer/operator
RUN/STOP

User level:
Operating mode:

programmer/operator
RUN/STOP

User level:
Operating mode:

5999.530-01B 13.08.98 WM

Page 36 /

Содержание 8600


















































Результаты поиска

Содержание 8600

Отзывы:

Похожие инструкции для 8600

Бренды по названию

Популярные бренды

Collamat 8600, Руководство по эксплуатации

Результаты поиска

Содержание 8600

Отзывы:

Похожие инструкции для 8600

Бренды по названию

Популярные бренды