Collamat 8600 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 49

background image

Speed and type of measurement

The

Speed

function is used to select the type of speed measurement and to adjust the

method of measuring. Three types of measurements are available:

Fixed speed

Incremental Encoder

Measuring Scanner

Fixed speed

At fixed speed the goods are labeled with a constant labeling speed. This speed is also
used when dispensing a label with the

Label jog

function of the

Labeling Mode

menu.

SPEED

DISPENSING SPEED

Method of measuring

Choice: Fixed

Value : 20.0 m/Min

Dispensing Speed

User level:

programmer/operator

Operating Mode:

RUN/STOP

Inkrementalgeber und messende Lichtschranke

When measuring the speed with an incremental encoder or by a measuring light barrier,
the speed of the goods is measured and they are labelled with this speed:

SPEED

INCREMENTAL ENCODER

Method of measuring

Choice:

Distance between

Incremental encoder

two Pulses : 1.00 mm

SPEED

DISTANCE BETWEEN

Method of measuring

the Lightbeams

Choice: Measuring

Scanner

Value : 14.0 mm

User level:

programmer

Operating Mode:

STOP

Note:
The distance of 14 mm applies for the standard light barrier of Collamat
Stralfors AG.
For more informations about the calculation of the speed measuring,
refer to the technical handbook Collamat

®

8600 and 9100

.

5999.530-01B 13.08.98 WM

Page 20 /

49

«
...
19
20
21
22
23
...
»

Содержание 8600


















































Отзывы:

Нет отзывов

Похожие инструкции для 8600

Бренд: 9BARISTA Страницы: 8

Бренд: LabelStation Страницы: 32

Бренд: Rancilio Страницы: 72

Бренд: Oki Страницы: 76

Бренд: Binatone Страницы: 50

Бренд: Summit Страницы: 28

Бренд: Hamilton Beach Страницы: 28

Бренд: Getinge Страницы: 4

Бренд: STARBUCKS Страницы: 9

Бренд: Bartscher Страницы: 93

Oracle Touch SES990BST

Бренд: Sage Страницы: 27

Бренд: U-Line Страницы: 66

Бренд: La Marzocco Страницы: 22

Бренд: Gaggia Milano Страницы: 88

Бренд: Cloer Страницы: 52

Бренд: Klarstein Страницы: 66

Бренд: MAKEiD Страницы: 11

Moccamaster KB 744

Бренд: techni vorm Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды