8
8
Dear customer,
Congratulations on your purchase of a Coleman
®
FastPitch
™
Air inlatable tent.
We take pride in bringing you a quality product which will offer you years of pleasure. Your new item is an investment which deserves
your care and attention. This manual has been compiled to help you to operate your product correctly. It contains details of the
product, its equipment, and information on its operation and maintenance. Read it carefully and familiarize yourself with the product
before using it.
CAUTION
It is the owner’s responsibility to make sure that all users will carefully read and follow the manual and
instructions for the safe operation of this product.
Important Notice:
Under Certain Weather conditions, condensation can occur on the inside surface of your tent.
To prevent condensation in your tent, please ensure adequate ventilation.
Condensation should not be confused with leaking.
1. SetUp/Inlation Instruction
1.1. Always practice at home prior to your irst usage on the campsite. Always follow the setup/inlation instructions written in this manual.
1.2. Find a lat piece of ground, far from trees to avoid falling branches, sap… that could damage your tent.
1.3. Be sure the area is clear of sharp stones, rocks, debris to avoid damaging the groundsheet.
1.4. Unpack the tent and clearly identify all separate parts of your tents – Tent, Poles bag, Stakes bag, Dual hand Pump and Manometer.
1.5. Unroll and lay your tent lat in the required position. Try to setup your tent with main entrance facing away from the wind.
1.6. Peg each corners of your tent – Those are clearly identiied by red coleman webbing loops - Ensure a proper tension between all
pegs and make sure the tent shape is rectangle. (Fig. A)
1.7. Your product is equipped with one type of valve: high pressure valve. There are located inside the tent and accessible through the
main doors and the small zipped openings. (Fig. B)
1.8. To inlate, open the valve cover by turning it anticlockwise. (Fig. c, D)
1.9. check and make sure the spring loaded pin is not depressed and locked in the open position. To verify that the valve is not open,
check the position of the pin. If the pin is down, the valve is opened. To close it, push the pin so it springs back up. Now the valve is
closed and ready for inlation.
1.10. All inlation is done in the
closed position
(Fig. 1) and delation is done in the
open position
. (Fig. 2)
1.11. To attach the pump hose to the high pressure valve, push the itting into the valve and turn clock wise to lock it (Fig. E, F, G). Inlate
until you have reached the required pressure of 5.5 - 6.5 PSI (379-448mbar). (Fig. h)
note:
To help the tent inlate to its correct structure a gentle lift on the inlatable sections maybe required.
WARNING
Do not over inlate your tent since pressure could increase during rising temperatures over your camping stay.
1.12. After inlation is done and you reached the correct pressure, disconnect the hose from the valve (turn the pump itting anticlockwise)
and close the valve cover.
note:
The valve will not be completely airtight until closed with the valve cover tightened.
1.13. Inlate all tent poles by reproducing §1.7 to §1.12.
1.14. If you own a FastPitch™ Air tent including iberglass pole(s) (front porch, side brow pole…), assemble the pole line by slotting
sections together – all sections are maintained with shock cords.
1.15. Insert the pole lines in their corresponding pole sleeves – matching poles sleeves and pole lines is done through color coding.
1.16. Insert all iberglass pole pin ends into corresponding plastic connectors (brow pole – Fig. J) or pin (front porch – Fig. I).
1.17. hinged Door Poles Set Up.
1.17.1 Insert Vertical Red Pole into sleeve and catch pole end caps into the plastic hinges - close the sleeve with zipper. (Fig 3)
1.17.2.
Insert Round Green Pole into the sleeve and catch pole end caps into the plastic hinges – close the sleeve with zipper.(Fig 4)
1.17.3. hinged Door is now ready to operate.
1.18. close all doors zippers.
1.19. Re-check the position of the 4-corner pegs – adjust if necessary.
1.20. Place all remaining pegs around the tent.
1.21. Peg all guy lines – always use all guy lines – Take care that tent is not distorted under guy lines tension by adjusting runner’s
position. check guy lines tension regularly along your stay.
1.22. If you suspect an air-leak, check that air valve is closed properly, both pin loaded spring and outer cover.
1.23. If air pole is still leaking, a complete check of the inner tube is needed. Please refer to maintenance part of this manual.
WARNING
Pressure will rise and decrease with increasing/decreasing temperature.
Regularly check pressure during prolonged stay (squeeze & feel air poles pressure).
If the temperature is rising and poles feels too hard, release some pressure by pushing briely on the valve pin
then, plug your pump and inlate to adjust to the recommended pressure.
GB
Содержание FAST PITCH
Страница 2: ...2 Fig A Fig D Fig F Fig B Fig C Fig E ...
Страница 3: ...3 Fig G Fig J Fig H Fig M Fig I Fig N ...
Страница 4: ...4 Fig O Fig R Fig S Fig P Fig Q ...
Страница 5: ...5 Fig 2 Fig 1 Fig 4 Fig 3 ...
