background image

6X-1110B

17

3.1.6  Installation Procedure

Provisions must be made for routing the system cable up to the camera system location:

• 

Pole mounting: if the cable routes up through the pole, support the cable inside the pole to strain 
relieve the camera connector.

• 

Pedestal mounting: route the cable down into the pedestal. The cable must be secured by a strain 
relief within the pedestal and must not be allowed to hang free through the pedestal.

The sequence of installation can vary from site to site:

• 

Verify that the system cable is accessible for connection to the camera system connector at the 
mounting location.

• 

Prepare wall for installation: use the mount as a template. Mark and drill holes in the mounting 
surface.

• 

Install large corner, large pole, and parapet mounts. For mounting on:

• 

A corner: Use the mount as a template. Mark and drill holes in the mounting surface. Posi-
tion the mount over the mounting holes. Secure with 5/16-inch fasteners (not supplied). 
Drill a hole for the cable if required. See Figure 6.

• 

A pole: Position the pole mount on the pole and secure with the stainless steel mounting 

straps (supplied). Use a flat blade screw driver or 5/16-inch socket wrench (not supplied) 

to tighten strap screws. See Figure 5.

• 

A parapet: Fasten the parapet mount adapter to the structure (see Figure 20):

1.  Slip the upper and lower mounting brackets onto the tube assembly. The bracket 

with the strap on the lower end is installed last. Seat the bottom of the tube 
against the strap and snug the U bolt.

2.  Hold the parapet mount assembly against the parapet and position it as far down 

as possible, so that the 6-inch flange clears the top of the parapet by one or two 

inches.

3.  Slide the upper mounting bracket up to the edge of the parapet (or as close to the 

edge as practical) and anchor the fasteners securely. Snug the U bolt and mark 
the drill pattern. 

4.  Drill holes, insert fasteners, and secure to parapet. 

• 

Install the adjustable head for a standalone camera system (see Figures 3-7):

• 

Attach the mounting bracket to the pedestal or wall mount with four 1/4-20 stainless steel 
screws (supplied).

• 

Attach the adjustable head to the mounting bracket with the bolt (supplied). 

• 

Install the wall mount. For mounting on:

• 

A wall: Position the wall mount over the mounting holes. Attach with four 5/16-inch fasten-
ers (supplied). See Figures 4 and 7.

Содержание ER 8800




























Отзывы: