CogniMem CM1K Скачать руководство пользователя

Страница: 47 / 61

CM1K Hardware User’s Manual

The first DS is sustained for four clock cycles to broadcast a vector of four components to the neurons. The REG

execute a Write LCOMP. The ID_l signal falls two clock cycles later indicating that the vector is recognized with

certainty by the firing neurons. The RDY signal falls as soon as the neurons start executing the first Write COMP

and remains low until the Write LCOMP is completed.

The second DS triggers a Read DIST. The RDY signal is pulled down for 18 cycles which is the duration of the Search

and Sort looking for the firing neuron with the smallest distance value. This distance is equal to 00 indicating an

exact match. The DIST_VAL pulse rises one clock cycle after the RDY signal to notify that DATA has been latched to

the RT_DIST register of the reco_logic.

The third DS triggers a Read CAT. The RDY signal is pulled down for 3 cycles only because a Search and Sort is not

necessary (it would extend the execution by 16 more cycles). This is no surprise since the ID_l signal has already

indicated that the input vector is recognized with certainty. The CAT_VAL pulse rises one clock cycle after the RDY

signal to notify that DATA has been latched to the RT_CAT register of the reco_logic.

Содержание CM1K






























































Результаты поиска

Содержание CM1K

Отзывы:

Похожие инструкции для CM1K

Бренды по названию

Популярные бренды

CogniMem CM1K, Руководство пользователя

Результаты поиска

Содержание CM1K

Отзывы:

Похожие инструкции для CM1K

Бренды по названию

Популярные бренды