Cognex DS900 Series Скачать руководство пользователя страница 39

Страница: 39 / 42

Error Codes

- indicates that the “state” LED lights for a longer time.

. indicates that the “state” LED lights briefly.

Flashing sequence

Cause

Remedy

Notes

Group: Loading / saving configuration

..
2x short

Mode not found.

Select different one.

Only previously stored
modes can be called up.

..-
2x short, 1x long

White error flash.

Contact manufacturer, return
sensor.

Should not occur in
normal operation.

...
3x short

Flash full.

None, contact manufacturer.

Should not occur in
normal operation.

....
4x short

Loading suppressed due to
active data transmission.

Stop active data transmission. Prevents PC software

crashes.

--...
2x long, 3x short

Data overflow during
transmission of the data via
Ethernet.

Reduce profile frequency,
increase packet size.

Data can be impaired.

--.....
2x long, 5x short

Error during calculation.

Reduce profile frequency,
select faster calculation
mode.

Data can be impaired.

--......
2x long, 6x short

Error during Ethernet
transmission.

Reduce profile frequency.

Data can be impaired.

Group: Data processing and transmission

--
2x long

Data overflow in the sensor.

Select smaller measuring
field, reduce profile
frequency, select less
complex measuring program.

Data can be impaired;
exposure time can be
longer than expected.

--.
2x long, 1x short

Data overflow during receipt
of the data from the sensor.

Select smaller measuring
field, reduce profile
frequency, select less
complex measuring program.

Data can be impaired.

--..
2x long, 2x short

Data overflow for serial port
RS422.

Reduce profile frequency,
select less complex
measuring program.

Data can be impaired.

Group: Ethernet Interface

----
4x long

IP Address conflict.

Check the Ethernet
configuration of device and
the host PC. Choose another
IP address for the device.

If the problem persists,
please contact the
manufacturer.

The "state" LED flashes green and

long

during active data transmission.

The "state" LED flashes green and

short

for controller accesses. A controller access can cause various data

overflows particularly if the measuring frequency is near its maximum.

Error Codes

Содержание DS900 Series











































Результаты поиска

Содержание DS900 Series

Отзывы:

Похожие инструкции для DS900 Series

Бренды по названию

Популярные бренды

Cognex DS900 Series, Справочная информация

Результаты поиска

Содержание DS900 Series

Отзывы:

Похожие инструкции для DS900 Series

Бренды по названию

Популярные бренды