background image

Page 6 of 12

Fusing Instructions (Independent Flashing Units):

LED  Fusing Considerations

Although the average current draw per module is very low, due to the type of circuit used to power each module, the instantaneous peak 

current to a module can be significantly higher during low voltage conditions. To avoid prematurely blowing ATO style fuses or tripping 

breakers it is recommended the following rule-of-thumb be used to size fuses or breakers. This is especially important in lightbars with many 

LED modules running off a single fused source.

Minimum fuse size calculation: 20A

For LED 12 volt electrical current

1.5  X (number of 4, 6, & 9LED modules being fused) = Total Electrical Current at 12.8 VDC or

0.5  X (number of 3LED modules being fused)             = Total Electrical Current at 12.8 VDC

LED MODULES

Operating Specifications for directional module:

 

 

Operating Voltage: 10-16 VDC, Reverse Polarity Protection

 

    

Current  Draw : Flashing Module

 

 

 

 

Red/Amber -  .25A avg @ 12.8 Volts

 

 

 

 

Blue/White    -  .4A avg @ 12.8 Volts

    

    Steady 

Burn 

Module

 

 

 

 

Red/Amber -  .5A avg @ 12.8 Volts

 

 

 

 

Blue/White     -  .8A avg @ 12.8 Volts

  

 

 

Available Colors - Red , Blue, Amber, and White

Fash Pattern Instructions (Independent Flashing Units):

CAUTION!

This product contains high intensity LED devices.  To prevent eye damage, DO NOT stare into the light beam at close range.

INSTALLER NOTE:

FLASH RATE + FLASH SEQUENCE = FLASH PATTERN

Lighthead Flash Sequences - Multi Color

LEFT / RIGHT

(DEFAULT):

PRIMARY & SECONDARY

PRIMARY ONLY - 

LEVEL - 1 DEFAULT

SECONDARY ONLY

PRIMARY W / SECONDARY POPS

PRIMARY W / SECONDARY RANDOM

EVEN / ODD:

PRIMARY & SECONDARY

PRIMARY ONLY - 

LEVEL - 2 DEFAULT

SECONDARY ONLY

PRIMARY W / SECONDARY POPS

PRIMARY W / SECONDARY RANDOM

RANDOM:

PRIMARY & SECONDARY

PRIMARY ONLY

SECONDARY ONLY

PRIMARY W / SECONDARY POPS

PRIMARY W / SECONDARY RANDOM

CYCLE SEQUENCE

RANDOM:

PRIMARY & SECONDARY

PRIMARY ONLY

SECONDARY ONLY

PRIMARY W / SECONDARY POPS

PRIMARY W / SECONDARY RANDOM

ALL ON

RANDOM:

PRIMARY & SECONDARY

SWEEP

LEFT / RIGHT:

SECONDARY ONLY

NULL:

ALL LIGHTHEADS OFF

Lighthead Flash Sequences - Multi Color

Double Flash-75 

LEVEL - 2 DEFAULT

Triple Flash-75
Quad Flash-75
Quint Flash-75
Double Flash-150
Triple Flash-150 

LEVEL - 1 DEFAULT

Quad Flash-150
Quint Flash-150
Triple Pop Flash-150
Quad Pop Flash-150
Single Flash-375
Cycle Rates

Содержание WingMan Flex Series













Отзывы: