Code Alarm CA- 550 Скачать руководство пользователя | Manualshive

Страница: 22 / 30

background image

Negative Lock Output / Positive Unlock Output (GREEN)
Negative Unlock Output / Positive Lock Output (BLUE)

Negative Second Door Unlock Output (BLUE/GREEN)

Reverse Polarity (5-Wire Doorlocks) and Reverse Polarity with 2-step Unlock

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.

Verification:

These wires will rest at ground and register positive voltage when the Lock and Unlock switches

are activated.

Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.

Verification:

This wire will rest at ground and register positive voltage when the driver’s door is unlocked.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in diagram 10 below. Use (1) Code Alarm
part DLRK (Door Lock Relay Kit, not supplied) or (2) Code Alarm part HDRLY (SPDT relay, not supplied).

Note: When adding the 2 step unlock feature the BLUE/GREEN 2nd door unlock wire will be used to unlock all

vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) (Code Alarm part
HDRLY) is required. Connect the relays as shown in diagram 11 to unlock the driver’s door on the first
press of unlock

6. DOOR LOCKS

30

87

87a

86

85

Cut

Fused +12 Volt
Battery Source

Lock

Unlock

Master Door
Lock Switch

X

30

87

87a

86

85

X

To Door Lock
Actuators

To Door Lock
Actuators

GREEN (-) Lock Output

BLUE (-) Unlock Output Or BLUE/RED
(-) 2nd Door Unlock Output When
Installing The 2-step Unlock Feature

Fused +12 Volt
Battery Source

Cut

Diagram 10

BLUE/GREEN

30

87

87a

86

85

BLUE (-) Unlock Output

To Unlock Side Of
Driver's Door Actuator

Fused +12 Volt
Battery Source

From Keyless Entry
Module Or Door
Lock/Unlock Relays

CUT

X

Diagram 11

«
...
20
21
22
23
24
...
»

Содержание CA- 550































Отзывы:

Нет отзывов

Похожие инструкции для CA- 550

Бренд: Python Страницы: 57

Бренд: NAPCO Страницы: 4

Бренд: Firex Страницы: 8

Бренд: Johnson Controls Страницы: 16

METASYS DH500 Series

Бренд: Johnson Controls Страницы: 32

Бренд: Letsfit Страницы: 12

Бренд: KRHÜNER Страницы: 12

Бренд: BURGprotect Страницы: 36

Бренд: PORTMAN Страницы: 28

Deep Sleep Revitalize HDS-3000

Бренд: HoMedics Страницы: 42

Бренд: HST Страницы: 36

Бренд: La Crosse Technology Страницы: 9

Бренд: Directed Electronics Страницы: 21

Бренд: Directed Electronics Страницы: 24

Бренд: Code Alarm Страницы: 34

Бренд: Cavius Страницы: 14

Бренд: DEI Страницы: 27

Бренд: Zeon Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды