Code Alarm CA- 550 Скачать руководство пользователя | Manualshive

Страница: 21 / 30

background image

6. DOOR LOCKS

Negative Lock Output / Positive Unlock Output (GREEN)
Negative Unlock Output / Positive Lock Output (BLUE)

Negative Second Door Unlock Output (BLUE/GREEN)

Positive Switching and Positive Switching with 2-step unlock feature:

All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.

Verification:

These wires will register positive voltage when the Lock and Unlock switches are activated.

Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.

Verification:

This wire will rest at ground and register positive voltage when the driver’s door is unlocked.

Connect the GREEN and BLUE or BLUE/GREEN wires shown in diagram 8 below.

Note: When adding the 2 step unlock feature the BLUE/GREEN 2nd door unlock wire will be used to unlock all

vehicle doors on the second press of unlock. Two additional SPDT relays (not supplied) (Code Alarm part
HDRLY) are required. Connect the relays as shown in diagram 9 to unlock the driver’s door on the first
press of unlock.

Lock

Unlock

Door Lock Switch

Vehicle Door Lock
Control Relays

BLUE (+) Lock Output

GREEN (+) Unlock Output

30

87

87a

86

85

To Unlock Side Of
Driver's Door Actuator

Fused +12 Volt
Battery Source

From Keyless Entry
Module Or Door
Lock/Unlock Relays

CUT

X

30

87

87a

86

85

BLUE/RED Second
Door Unlock Trigger
From Control Module

Fused +12 Volt
Battery Source

Chassis Ground

Diagram 9

BLUE/GREEN

«
...
19
20
21
22
23
...
»

Содержание CA- 550































Отзывы:

Нет отзывов

Похожие инструкции для CA- 550

Бренд: IEH Страницы: 32

Бренд: Accenda Страницы: 16

Superflow UG-5-AFR-230V-MB

Бренд: CALECTRO Страницы: 4

Бренд: Memorex Страницы: 42

Бренд: Ebode Страницы: 36

Ampac TITANUS PRO-SENS

Бренд: Halma Страницы: 197

Prestige APS-15CH

Бренд: Audiovox Страницы: 5

Бренд: Siemens Страницы: 2

TITANUS SuperSens

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 4

Бренд: IKEA Страницы: 8

Бренд: Bentel Security Страницы: 4

FireClass FC400P

Бренд: Bentel Security Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды