manualshive.com logo in svg

Code Alarm CA- 550, Руководство по установке

Поделиться
Скачать
Code Alarm CA- 550 Скачать руководство пользователя страница 11

Negative Door Input   (GREEN)

Locate the vehicle’s dome light or door pin switch wire.

Verification: This wire will register ground (NEG) when the door is opened and the interior light is on.  This
wire will register positive voltage when the door is closed and the interior light is off.

Connect the GREEN wire to the vehicle’s negative door input wire(s).

Positive Door Input (PURPLE)

Locate the vehicle’s dome light or door pin switch wire.

Verification: This wire will register positive voltage(POS) when the door is opened and the interior light is on.
This wire will register ground or "0" Volts when the door is closed and the interior light is off.

Connect the PURPLE wire to the vehicle’s negative door input wire(s).

Chassis Ground Source (BLACK)

Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not
supplied). Scrape away paint from the grounding point to ensure a good connection.  The recommended
grounding point is a painted metal surface in the driver’s side kick panel area.

Note: Do not ground the BLACK wire with any other vehicle components.

Ground When Armed Output (ORANGE)

This wire will show Ground when the system is Armed

This wire is used for controlling window modules or additional sensors

Headlight Output  (LT. GREEN/ORANGE)

Locate the vehicle’s headlight wire

Verification: 

This wire will register either positive voltage or ground when the headlights are turned on

Connect the LT. GREEN/ORANGE to the vehicles headlight wire if the system is negative. (LOW CURRENT
ONLY)

Connecting to a Positive Headlight Output

2.  22 PIN BASE HARNESS CONTINUED

30

87

87a

86

85

GREEN/ORANGE Headlight
Output From Control Module

To Vehicle Headlight
            Wire

Fused +12 Volt
 Battery Feed

Fused +12 Volt
 Battery Feed

Содержание CA- 550































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды