background image

Revision 0, 09/09 - Instruction Book Part No. T16417

©2009 Public Safety Equipment, Inc. Printed in USA

PRODUCT RETURNS

If a product must be returned for repair or replacement*, please contact our factory to obtain a Return 

Goods Authorization Number  (RGA number) before you ship the product to Code 3, Inc.  Write the RGA number 
clearly on the package near the mailing label.  Be sure you use suffi cient packing materials to avoid damage to 
the product being returned while in transit.

*Code 3, Inc. reserves the right to repair or replace at its discretion.  Code 3, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or 

reinstallation of products requiring service and/or repair.; nor for the packaging, handling, and shipping: nor for the handling of products return to sender after the service has been 
rendered.

Code 3, Inc.

10986 N. Warson Road

St. Louis, Missouri 63114-2029—USA

Ph. (314) 426-2700  Fax (314) 426-1337

www.code3pse.com

WARRANTY

Code 3, Inc.'s L.E.D. emergency devices are tested and found to be operational at the time of manufacture.  

Provided they are installed and operated in accordance with manufacturer's recommendations, Code 3, Inc. guarantees 
all parts and components except the lamps to a period of 1 year, LED Lighthead modules to a period of 5 years (unless 
otherwise expressed) from the date of purchase or delivery, whichever is later.  Units demonstrated to be defective 
within the warranty period will be repaired or replaced at the factory service center at no cost.

Use of lamp or other electrical load of a wattage higher than installed or recommended by the factory, or use 

of inappropriate or inadequate wiring or circuit protection causes this warranty to become void.  Failure or destruction 
of the product resulting from abuse or unusual use and/or accidents is not covered by this warranty.  Code 3, Inc. 
shall in no way be liable for other damages including consequential, indirect or special damages whether loss is due 
to negligence or breach of warranty.

CODE 3, INC. MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING, WITHOUT LIMITA-

TION, WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH RESPECT TO THIS PRODUCT.

8

PROBLEMS OR QUESTIONS? CALL OUR TECHNICAL ASSISTANCE HOTLINE (314) 996-2800

WWW.CODE3PSE.COM

Code 3

®

 is a registered trademark of Code 3, Inc., a subsidiary of Public Safety Equipment, Inc.

Содержание LSS222









Отзывы: