Code 3 LED X 2100 Скачать руководство пользователя страница 15

Страница: 15 / 16

Follow the guide below for information on repair and trouble shooting for the arrowstik option.

ARROWSTIK

OPTION

TROUBLESHOOTING GUIDE

PROBLEM

Arrowstik does not
function when
turned on.

Lamp or LED
module does not
come on when it
should.

POSSIBLE CAUSE

a. Check plug in rear of

control box.

a. Check power and ground

connections.

a. Bad lamp or defective

LED module.

b. Defective wiring connection.

a. Control box is damaged.

SOLUTION

a. Reconnect plug.

a. Reconnect ground/power.

a. Replace lamp or LED
module.
b. Repair connection.

c. Return to Code3.

QUESTIONS

Are the front
panel LED
indicators
operating
properly?

Yes

Are the front
panel LED
indicators
functioning
properly?

Yes

Note:

LED modules have no user serviceable parts. Replace entire module if

found defective.

Notes:

Содержание LED X 2100

















Результаты поиска

Содержание LED X 2100

Отзывы:

Похожие инструкции для LED X 2100

Бренды по названию

Популярные бренды

Code 3 LED X 2100, Руководство по установке и эксплуатации

Результаты поиска

Содержание LED X 2100

Отзывы:

Похожие инструкции для LED X 2100

Бренды по названию

Популярные бренды