COBHAM D-MINI 4B-AK Скачать руководство пользователя страница 35

Страница: 35 / 81

DIGIMINI EMEA/APAC/AUSTRALIA REPEATERS

PRODUCT DESCRIPTION AND USER’S MANUAL

Cobham Wireless

–

Coverage

Date: 11-Oct-15

www.cobham.com/wireless

Document number: 00030UMCD

Rev. 5.0

Page |

4-9

7. Carefully, connect the supplied flat cable between the two connectors as shown below.

Verify that the flat-cable is securely connected.

NOTE: Handle Flat Cable with care when connecting.

Figure 4-10. Interconnecting Flat cable

8. Referring to the following sections, choose the appropriate COVER PLATE and LABEL according

to the type of unit combination that comprises the quad-band assembly section

4.5.2.

9. Cover the flat-cable with the appropriate Flat Cable Cover Plate and secure using the four

screws.

NOTE: All labels refer to Band-1 and Band-2. The band frequencies for each repeater are

located on a sticker on the SIDE of the repeater. (e.g for DIGImini 900/2100, “Band 1” is 900

and “Band 2” is 2100).

Figure 4-11. Assembling Interconnecting Cover Plate

Plate covering flat
cable

Содержание D-MINI 4B-AK


















































































Результаты поиска

Содержание D-MINI 4B-AK

Отзывы:

Похожие инструкции для D-MINI 4B-AK

Бренды по названию

Популярные бренды

COBHAM D-MINI 4B-AK, Руководство пользователя

Результаты поиска

Содержание D-MINI 4B-AK

Отзывы:

Похожие инструкции для D-MINI 4B-AK

Бренды по названию

Популярные бренды