Cobalt Digital Inc +EAS Скачать руководство пользователя страница 12

10

EAS OPTION (+EAS) MANUAL SUPPLEMENT

OPT-SW-PHXEAS-MS (V1.1)

Where +EAS is licensed for a card/device, the Event Setup > 
Event Triggers
 sub-tab has added choices associated with EAS 
actions. 

An added EAS trigger column exposes EAS actions that can be 
used as triggers to activate other actions. These triggers and 
actions can be used with other card/device attributes to step into 
and out of EAS modes and normal operation (as shown in the 
example below). The Event Action column also has choices that 
allow actions upon other triggers (such as GPI) to start and stop 
EAS (also shown in an example below).

Event Setup Controls

Table 1

+EAS Option Control List and Descriptions — continued

In the example here for Event 3 and Event 4, when a Crawl Start or Crawl Stop event has been detected, these events can 
serve as triggers to respectively invoke user preset “Go to EAS Audio Route” or “Go to Norm1A Audio Route”. These presets 
would be user-defined presets that perform special audio routing when a crawl is active, and resume to normal after the crawl 
has stopped.

Note: • Refer to Product Manual for detailed descriptions of the Event Setup tab and its sub-tabs, which contains 

important information regarding the use of event presets and actions.

In the example here for Event 1 and Event 2, GPI 1 is being used to start (and optionally) stop the crawl when 

EAS > General 

Setup

 is set to use Event Triggered operation. Note that while the Event 2 EAS Stop Trigger is not necessary to stop the crawl, 

the defined event here is useful should the need arise to abort the crawl sooner than its full content playout (as in the case of an 
erroneous “false alarm”). (A GPI correlated to an EAS Stop Trigger can be used to immediately stop a crawl even if all the crawl 
text has not yet been displayed.) Also note that EAS crawl for a given message ceases after the Crawl Loop Count is exhausted. 

Note: Although EAS Start Trigger starts an EAS text crawl, if no EAS message has been received, no text crawl will be generated.

Содержание +EAS



















Отзывы: