Coats XR 1750 Скачать руководство пользователя

Страница: 37 / 40

Important: Always read and follow the on-screen operating instructions.

• 31

Viid

o B

alla

ciif

fiic

tiio

Cycle Time

8 seconds (average 50 pound tire)

Maximum Outside Tire Diameter

44 inches

Maximum Tire/Wheel Weight

160 pounds (72 kg)

Wheel Diameter Range (with Offset Arm or

Manual)

10 - 24 inches

Wheel Width Range

2 - 20 inches

Balancing Display Increments

0.25 or 0.01 ounces

Resolution (Non-Round Off Mode)

0.01 ounce, position 0.70 degrees

Resolution (Round Off Mode)

0.25 ounce, position 0.70 degrees

Temperature at Balancer Location

50 degrees - 105 degrees Fahrenheit

Mounting Shaft Diameter

40 MM standard

Electrical (115 V, 1 Ph, 60 Hz)

standard 15 AMP 3-prong outlet
Australia (230 V, 1 Ph, 50 Hz)

Shipping Weight

680 pounds (308 Kg)

Net Weight with Standard Accessories

465 pounds (211 Kg)

Balancer RPM

185 - 205 RPM

• 17 inch VGA CRT Monitor w/Tilt and Swivel

Adjustments

• Automatic Data Entry for Offset, Diameter, and

Width (if equipped), - Manual Entry Backup on all
Parameters

• Interactive Screens for all Modes and Functions

with Superior Graphic Displays

• Static-on-Screen™

• Four Fixed Function Keys, Seven Program Keys for

user Friendly Operation

• Many Balancing Modes

Dynamic (Standard): Clip-on Weights

4 Alloy: User Defined

2 PAX: User Defined

4 Static

Patch Type Weights: Static Only

Behind the Spoke Weight Placement
(All Modes with Inside Wheel Weights)

• Auto Start When Hood is Lowered

• Vertical Wheel Mounting System

• Single Spin Balancing - Dynamic and Static

• Easy-To-Read Position Indicators

• Interactive Tape-A-Weight™ Placement with Offset

Arm

• Cone Spring Permanently Retained in Faceplate

• Hood Safety Interlock System

• Extended Mounting Faceplate for Deeper Wheels

• Removable Center Shaft for Closed Center Wheels

• Match Mount (Optimization) Function with Weight

Optimization Program

• Can be Programmed for Four Different Users

• User Friendly Weight and Position Calibration

• Easy Calibration of Automatic Data Entry Devices

• No Bolt-down Installation

• Solid State Motor Control

• UL/CSA Listing

Содержание XR 1750








































Результаты поиска

Содержание XR 1750

Отзывы:

Похожие инструкции для XR 1750

Бренды по названию

Популярные бренды

Coats XR 1750, Руководство по установке

Результаты поиска

Содержание XR 1750

Отзывы:

Похожие инструкции для XR 1750

Бренды по названию

Популярные бренды