background image

Issue 6 31/1/14  - CMS Marine - +44 (0) 1452 380100 – [email protected] 

 

 

 

 

 

Page 2 

Welcome

 

Thank you for choosing CMS Marine to supply your SonicShield Product. 

Please ensure you read this installation guide fully before proceeding as correct installation is critical to 
the overall success of your Ultrasonic system 

If you have any questions or require any help please either contact us on +44 (0) 1452 380100 or 

[email protected]

 

Safety Considerations 

WARNING 

You MUST install this product in accordance with this installation guide, failure to follow the information 
enclosed could result in damage to your vessel or personal injury 

You MUST ensure you protect the permanent live connection with a 10 amp Inline fuse. Incorrect 
electrical installation could cause irreparable damage to the product or other electrical equipment and 
could result in personal injury or damage to the vessel. 

If you are not competent working with a 12V or 24V supply please contact a qualified Marine Electronics 
installer or contact CMS Marine to discuss installation. 

You MUST also be qualified to make any alterations or additions to your 110V – 240V AC supply if 
necessary. Modifications to your AC system are outside of the scope of this guide. 

PLEASE ENSURE ALL POWER IS SWITCHED OFF WHEN CONNECTING OR REMOVING CABLES FROM THE 
INTELLIGENT CONTROL UNIT. 

IF IN DOUBT PLEASE SEEK PROFESSIONAL ADVICE. 

 

 

 

 

 

Содержание SonicSheild III

















Отзывы: