manualshive.com logo in svg

CMP PowerClean Salt Econ, Инструкции по установке и руководство по эксплуатации товара

Поделиться
Скачать
CMP PowerClean Salt Econ Скачать руководство пользователя страница 3

3

A. SAFETY INSTRUCTIONS & PRECAUTIONS

IMPORTANT SAFETY INSTRUCTIONS. 

READ AND FOLLOW ALL INSTRUCTIONS

WARNING

WARNING

To reduce the risk of injury, do not permit children to use this product unless they are closely 

supervised at all times.

Risk of Electric Shock. Connect only to a grounding type receptacle protected by a ground-fault 

circuit-interrupter (GFCI). Contact a qualified electrician if you cannot verify the receptacle is 

protected by a GFCI.

Always follow all local building and electrical codes.

Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other 

equipment.

To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; 

provide a properly located outlet.

WARNING

WARNING

CAUTION

This product can form hazardous gas if not installed or operated correctly.

CAUTION

[For swimming pool pumps with or without a maximum 3-foot (0.91-m) cord] This chlorinator 

is for use with permanently installed pools and may also be used with hot tubs and spas if so 

marked. Do not use with portable pools. A permanently-installed pool is constructed in or on the 

ground or in a building such that it cannot be readily disassembled for storage and reassembled 

to its original integrity.

NOTICE

SAVE THESE INSTRUCTIONS

ELECTRICAL HAZARD

•  All Powerclean Salt systems are shipped from the factory wired for 220 Volts.

•  To reduce risk of electrical shock make sure all power to pool equipment area is off prior to any installation or removal of 

Powerclean Salt System components.

•  Immediately replace damaged Control Center cord.

•  Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers and other equipment.

•  Severe shock or injury will likely occur as a result of drill or drill cord coming in contact with water. Never allow electric drill 

or cord to come in contact with water. Only plug drill into a Class A (5 Milliampere Trip) protected Ground Fault Circuit 

Interrupter (GFCI) in accordance with the National Electrical Code Section 680 (USA ONLY). Please see your drill owner’s 

manual for further safety precautions.

•  Install the Control Center at least 10 feet from the inside walls of a pool to prevent any possibility of the unit coming in 

contact with water.

•  The Powerclean Salt Chlorinator has been designed with an internal electronic flow sensing tab. This device automatically 

switches the power to the electrolytic cell “OFF” when the water through the cell stops. To prevent cell damage and/or 

personal injury, do not in any way interfere with this system which has been designed for your protection.

Содержание PowerClean Salt Econ

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды