Club Car Carryall 1 Скачать руководство пользователя страница 123

Страница: 123 / 176

MOTOR (MODEL 5BC59JBS6390)

Motor

2008-2011 IQ System Electric Vehicle Maintenance and Service Supplement

Page 16a-5

16A

MOTOR COMPONENT TESTING AND INSPECTION

See General Warning, Section 10, Page 10-1.

ARMATURE

Visual Inspection

Disassemble the motor and carefully inspect the armature for the following characteristics:

•

Burned, charred or cracked insulation

•

Improperly cured varnish

•

Thrown solder

•

Flared armature windings

•

Damaged armature core laminations

•

Worn, burned or glazed commutators

•

Dirty or oily commutators

•

Raised commutator bars

•

Worn armature bearing or shaft

A dirty or oily commutator should be cleaned and wiped dry. Abnormalities identified during the inspection can
help determine original cause of failure. Slight roughness of the commutator can be polished smooth with 400
grit or finer sandpaper.

See following CAUTION and NOTE.

CAUT ION

• Do not use emery cloth to polish the commutator. Particles of emery are conductive and may

short-circuit the commutator bars. Do not use oil or lubricants on the commutator or brushes.

NOTE:

Oil on the commutator may indicate a faulty transaxle input shaft oil seal.

Armature Ground Test

CAUT ION

• Do not submerge the armature in solvent.

NOTE:

Before testing the armature, wipe it clean with a clean cloth. Remove any carbon dust and metal
particles from between the commutator bars.

1. With a multimeter set to 200 ohms, place one probe on the commutator and the other on the armature

core. The multimeter should indicate no continuity

(Figure 16a-6, Page 16a-6)

. If the reading is incor-

rect, replace the armature.

Содержание Carryall 1

















































































































































































Результаты поиска

Содержание Carryall 1

Отзывы:

Club Car Carryall 1, Дополнение к руководству по обслуживанию и ремонту, Страница: 123 / 176

Результаты поиска

Содержание Carryall 1

Отзывы: