USER MANUAL :
DOCUMENT NAME
When using a simcard to connect to a GSM network, there are a couple of parameters that your GSM service provider wi
need from you in order to connect to their network. These are sometimes not necessary as the card will automatically
connect but most will require them. The parameters are the NBIoT band and scrambling, APN Name, APN Username and
APN Password and are entered in the 'Communications Setup' section.
Depending on where you are in the world, NBIoT networks operate on different bands. This information can be provided to
you by your NBIoT service provider. Alternatively, setting it '0' will cause the logger to
it finds the active one. Consider though, this will delay the connection time for the logger which will ultimately impact on
the battery. It is therefore advisable to establish the active NBIoT band and enter it into
get this information, you could select the '0' option, wake the logger up, and check to which band it connected in the
diagnostic streaming option. This parameter can then be changed to that value preventing the logger
all the bands on later connections.
Data scrambling should be activated by default and will be used should your network support it.
Networks generally require you to enter the APN Name but the Username and Password are not necessary.
are obtained directly from your GSM service provider and most are published on their websites.
Cloudworks devices are also designed to allow
the APN details here will result in the device connecting to your private network.
address which will be shown in the 'Local IP' field in the 'General Details' box.
All Cloudworks devices connect to a server with a static IP or domain na
by default, on port 13000. If you are running your own server, the Server Name or IP address as well as Server Port number
need to be entered here.
Just a note, it is always better to rather use the IP add
that the logger will not have to execute a domain name lookup before connecting to your server. This is especially
important for NBIoT networks because of their slow communications properties.
Cloudworks loggers support the use of simcard pin codes. How this works is
will request the pincode when the modem powers up and starts connecting to the network. If the pincode field here is
populated, the logger will offer this code to the network, allowing it to connect. Failure of the pincode will cause the
logger to abort the connection attempt and shutdown.
If you are using a foreign simcard on a network, the logger will need to be told that it is allowed to use data roam
Without that, the logger will shutdown.
MANUAL : CDS546 NIMBUS LOOP LOGGER
NAME
CLASSIFICATION
DATE
PAGE
When using a simcard to connect to a GSM network, there are a couple of parameters that your GSM service provider wi
need from you in order to connect to their network. These are sometimes not necessary as the card will automatically
connect but most will require them. The parameters are the NBIoT band and scrambling, APN Name, APN Username and
tered in the 'Communications Setup' section.
Depending on where you are in the world, NBIoT networks operate on different bands. This information can be provided to
you by your NBIoT service provider. Alternatively, setting it '0' will cause the logger to automatically scan all the bands until
it finds the active one. Consider though, this will delay the connection time for the logger which will ultimately impact on
the battery. It is therefore advisable to establish the active NBIoT band and enter it into this field. Should you not be able to
get this information, you could select the '0' option, wake the logger up, and check to which band it connected in the
diagnostic streaming option. This parameter can then be changed to that value preventing the logger
Data scrambling should be activated by default and will be used should your network support it.
Networks generally require you to enter the APN Name but the Username and Password are not necessary.
are obtained directly from your GSM service provider and most are published on their websites.
devices are also designed to allow for the connection to custom private APN's for purposes of security. Entering
ll result in the device connecting to your private network. These networks normally issue a static IP
address which will be shown in the 'Local IP' field in the 'General Details' box.
All Cloudworks devices connect to a server with a static IP or domain name. They usually use UDP/IP protocols and connect,
by default, on port 13000. If you are running your own server, the Server Name or IP address as well as Server Port number
Just a note, it is always better to rather use the IP address than the domain name. This will mean
that the logger will not have to execute a domain name lookup before connecting to your server. This is especially
important for NBIoT networks because of their slow communications properties.
pport the use of simcard pin codes. How this works is - should a simcard have a pincode activated, it
will request the pincode when the modem powers up and starts connecting to the network. If the pincode field here is
s code to the network, allowing it to connect. Failure of the pincode will cause the
logger to abort the connection attempt and shutdown.
If you are using a foreign simcard on a network, the logger will need to be told that it is allowed to use data roam
PAGE
When using a simcard to connect to a GSM network, there are a couple of parameters that your GSM service provider will
need from you in order to connect to their network. These are sometimes not necessary as the card will automatically
connect but most will require them. The parameters are the NBIoT band and scrambling, APN Name, APN Username and
Depending on where you are in the world, NBIoT networks operate on different bands. This information can be provided to
automatically scan all the bands until
it finds the active one. Consider though, this will delay the connection time for the logger which will ultimately impact on
this field. Should you not be able to
get this information, you could select the '0' option, wake the logger up, and check to which band it connected in the
diagnostic streaming option. This parameter can then be changed to that value preventing the logger from having to scan
Networks generally require you to enter the APN Name but the Username and Password are not necessary. These details
the connection to custom private APN's for purposes of security. Entering
These networks normally issue a static IP
me. They usually use UDP/IP protocols and connect,
by default, on port 13000. If you are running your own server, the Server Name or IP address as well as Server Port number
ress than the domain name. This will mean
that the logger will not have to execute a domain name lookup before connecting to your server. This is especially
should a simcard have a pincode activated, it
will request the pincode when the modem powers up and starts connecting to the network. If the pincode field here is
s code to the network, allowing it to connect. Failure of the pincode will cause the
If you are using a foreign simcard on a network, the logger will need to be told that it is allowed to use data roaming.
