background image

Federal Communication Commission Interference Statement 

 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one of the following 
measures: 
. Reorient or relocate the receiving antenna. 
. Increase the separation between the equipment and receiver. 
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
. Consult the dealer or an experienced radio/TV technician for help. 
 

FCC Caution

: To assure continued compliance, any changes or modifications not expressly approved by 

the party responsible for compliance could void the user's authority to operate this equipment. (Example - 
use only shielded interface cables when connecting to computer or peripheral devices). 

 
FCC Radiation Exposure Statement 

 

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled 
environment. This equipment should be installed and operated with a minimum distance of 20 centimeters 
between the radiator and your body. 
 
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 
 
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm 
from all persons and must not be co-located or operating in conjunction with any other antenna or 
transmitter. 
 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) This device must accept any interference 
received, including interference that may cause undesired operation. 

 

 

                                                                               

     

 

Содержание KPT-32







Отзывы: