background image

REMOTE KEYPAD with NFC Tag (KPT-32)                            

 

Identifying the Parts 

 

 

 

1. Siren 

2. Orange LED: Home Arm Key 

3

Red LED: Away Arm Key

 

4. Panic Alarm (if enabled)   

   

 

- Press both 1 and 3 to trigger panic alarm

 

5. Fire Alarm (if enabled)         

- Press both 4 and 6 to trigger fire alarm

 

6. Medical Alarm (if enabled)    

- Press both 7 and 9 to trigger Medical alarm 

7. 

 Key 

- Enter Keypad PIN Code + 

 Key to enter Test Mode. 

8. Keypad Sensor (for tag) 

9. NFC Tag 

10. # Key 

11. Mounting Holes 

12. Tamper Switch

<NOTE>   

 

 

A short beep will sound along with key pressing to indicate that the button pressed is valid. 

 

A long beep will sound along with key pressing to indicate successful command. 

 

4 continuous beeps will sound indicating mistake and the user should repeat the process again. 

 

Backlight will be ON for any key pressed or command sent from the Keypad.   

 

LED Indicator 

 

Red LED (Away Arm Key) 

 

Red LED on: 

the system is in 

Test Mode

.

 

 

Red LED: 

Red flashes, and Backlight on

 

in the

 Away Arm Mode. 

 

Red LED flash 

with 4 beeps:

 

failure due to the following reasons: 

 

No response from the control panel. 

 

Request for 

Home mode

 during 

Arm mode

 

Request for 

Force arm

 

Orange LED (Home Arm Key) 

 

 

Orange LED: 

Orange flashes and backlight on in the 

Home Mode

.

 

 

Orange LED flashes for 5 seconds: 

low battery in Normal Operation Mode, and Tamper open.

 

 

LED flash 

with 4 beeps

failure due to the following reasons: 

 

No response from the control panel. 

 

Request for 

Home mode

 during 

Arm mode

 

Request for 

Force arm

 

                                                                               

     

 

Содержание KPT-32







Отзывы: