Cleveland KET-12-T Скачать руководство пользователя страница 2

Страница: 2 / 32

Shut off power at main
fuse disconnect prior
to servicing.

Ensure kettle is at room
temperature and pressure
gauge is showing zero or less
prior to removing any fittings.

Inspect unit daily for
proper operation.

Do not fill kettle above
recommended level
marked on outside of kettle.

Surfaces may be
extremely hot! Use
protective equipment.

Keep appliance and area free
and clear of combustibles.

Stand clear of product
discharge path when
discharging hot product.

Wear protective equipment
when discharging hot product.

Do not lean on or place
objects on kettle lip.

Do not attempt to operate
this appliance during a
power failure.

Keep clear of pressure
relief discharge.

Keep hands away from
moving parts and pinch points.

SERVICING

IMPORTANT

CAUTION

DANGER

GAS APPLIANCES

For your safety

Содержание KET-12-T

































Результаты поиска

Содержание KET-12-T

Отзывы:

Похожие инструкции для KET-12-T

Бренды по названию

Популярные бренды

Cleveland KET-12-T, Руководство оператора

Результаты поиска

Содержание KET-12-T

Отзывы:

Похожие инструкции для KET-12-T

Бренды по названию

Популярные бренды