Cleveland CET-5 Скачать руководство пользователя страница 3

INTRODUCTION 

To get the full advantage of steam cooking, your Cleveland/ALCO equipment must be properly installed. A steamer which is 
improperly installed, improperly used, improperly maintained, or improperly repaired will create a dangerous condition and 
may cause injury to personnel. 

Your Cleveland/ALCO equipment will require minimum servicing provided it is operated according to instructions 
and given the care recommended. 

Make

 sure

 that responsible personnel understand how your steam cooking equipment should be operated and cared tor. 

Proper use and maintenance pay handsome dividends in long life and satisfactory performance. 

Safe steam cooking equipment operation dictates that every owner of steam cooking equipment should follow these rules tor 
operational safety: 

1) Begin a comprehensive, continuous program of internal and external steam cooking equipment inspection. 

2) Never allow untrained personnel to operate or experiment with a steamer. 

3) At the end of each day's operation — 

— Remove any spilled food, then wash the racks and compartment interiors thoroughly with mild detergent in warm 

water.

 

— Rinse thoroughly with dean warm water. 

— Let rinse water drain through compartment drain opening. If water does not drain freely, drain lines must be 

cleaned out before cooking again. Clogged or slow drains are dangerous because hot water may spill out 
when compartment doors are opened after a cooking cycle. 

— When cleaning the steamer's exterior, never apply water to controls on the console. Use a damp cloth for 

cleaning. 

4) Always leave the compartment door ajar when the compartment is not in use. 

5) Shut the unit down at the end of each day's operation

 as

 follows  — 

— On boiler-equipped steamers, blow down the boiler. For specific information, refer to "Ste am Generators  • 

Maintenance Procedures." 

— On direct-connected steamers, cut off the main steam supply with a valve ahead of the steamer's pressure 

reducing valve. 

— On SteamCraft II models, (one compartment counter-top model) depress the power switch to  the "off" 

position. 

6) Read and follow The Cleveland/ALCO instructions on steamer and steam generator maintenance and servicing 

in the

 Owners

 Manual before making any adjustments or replacement

 of

 pans, or decision to buy parts, or 

before calling tor

 service.

 

7) Use only replacement parts which are factory authorized as equivalent to the parts being replaced, to preserve 

the certification of Underwriters Laboratories, American Gas Association, Canadian Standards Association or 
Canadian Gas Association (as applicable). 

8) Never allow unqualified personnel to tamper with the steamer or steam generator controls, or to replace worn-

out parts 

9) For gas-fired steam generators (boilers): Post in a prominent location instructions to be followed in the event 

the us er smells gas. This information shall be obtained by consulting the local gas supplier. 

FOR YOUR SAFETY

 

Do not store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance. 

CLEVELAND RANGE, INC., 1333 EAST 179th ST., CLEVELAND, OHIO 44110 

Manufacturer reserves right of design improvement or modification,

 as

 warranted.

 

LITHO  IN USA. 0388 

Next Page 

Содержание CET-5


































Отзывы: