CLEOPATRA Cleo Premium Pro 1532 Скачать руководство пользователя

Страница: 44 / 52

Switch SW1 and push-buttons SW2...SW4

The switch SW1 (door switch) and the pushbuttons SW2 (steam bath On/

Off), SW3 (Light 1 On/Off) and SW4 (Light 2 On/Off) are connected to the

appropriate terminals of terminal bloc “X31” on the steam bath board.

Note: If no door switch (SW1) is connected the terminals “DOOR” and “24V”

must be short circuited using a cable bridge.
The crosssection of the connecting cable must comply with the applicable

local regulations.

Connection of the remote terminal (Option RP)

The optional remote terminal is to be connected via a fourwire cable to the

corresponding contacts of terminal block X15 on the power board of one

of the humidifiers.
Addtional humidifiers (max. 8) to be remote controlled are connected in

series via the contacts “D+” and “D–” of terminal block X15 to the humidifier

connected to the remote terminal using a twowire cable.
The maximum cable length between the units is 50 m. Cable section

0.5 mm

The termination of the remote terminal bus is established via the jumpers

JP1, JP4 and JP5 on the power boards of the remote terminal and the con

nected humidifiers (see table below).

Jumper settings for operation with optional remote terminal

Jumper

Function

Remote terminal

Unit(s)

in between

Last unit in

the chain

JP1

120Ω end resistor

JP4

Pull up resistor

JP5

Pull down resistor

LINK UP

EXTERNAL

CON.

CURRENT SENSOR

315mAT

from contactor

to cylinder

Cleo Premium Pro

ext.

REMOTE

D+ D– GND 5V 24V

X15

Unit 2

Unit 3

Last Unit

D+ D–GND 5V 24V

X15

D+ D–GND 5V 24V

X15

D+ D–GND 5V 24V

X15

JP1 JP4 JP5

Remote Terminal

D+ D–GND 5V 24V

X15

JP1 JP4 JP5

Содержание Cleo Premium Pro 1532





















































Результаты поиска

Содержание Cleo Premium Pro 1532

Отзывы:

Похожие инструкции для Cleo Premium Pro 1532

Бренды по названию

Популярные бренды

CLEOPATRA Cleo Premium Pro 1532, Инструкция по монтажу

Результаты поиска

Содержание Cleo Premium Pro 1532

Отзывы:

Похожие инструкции для Cleo Premium Pro 1532

Бренды по названию

Популярные бренды