background image

 

1

 / 9 

No. 999-1009, Min’an Avenue, Xiang’an                                                                                                      18/20 Duerdin , 

Xiamen China 361006                                                                                                                             Clayton VIC 3168 
Tel: +86-592-5781288                                                                                                                      Tel: +61-3-90176688 

Fax: +86-592-5782298                                                                                                                    Fax: +61-3-90176668 
Email: 

[email protected]

                                                                                              Email: 

[email protected]

 

Website: 

www.clenergy.com.cn

                                                                                            Website: www.clenergy.com.au 

 

1. Product Introduction 

Clenergy PV-ezRack SolarMatrix is a mounting system with tilt angle 5 °, 10 °, 15 ° 

and 20 ° and suitable for non-penetrating roof in medium wind load region where 

wind speed is within 40m/s. The system could be installed easily with simple tools.  

 

 

Please  review  this  manual  thoroughly  prior  to  installing  PV-ezRack  SolarMatrix. 

This  manual  provides  supporting  documentation  for  building  permit  applications 

relating to PV-ezRack SolarMatrix Mounting system.

  

 

When installed in accordance with this guide, the PV-ezRack SolarMatrix parts will 

be  structurally  adequate  and  adhere  to  AS/NZS1170,  IBC2006  and  California 

2007  building  code.  During  installation  please  comply  with  the  appropriate 

occupational  health  and  safety  regulations.  Please  also  pay  attention  to  other 

relevant  regulations  of  your  local  region.  Please  check  that  you  are  using  the 

latest  version  of  the  installation  manual  by  contacting  Clenergy  via  email  at 

[email protected]

or by contacting your local distributor.

 

 

 
 
 
 
 
 

 

Содержание PV-ezRack SolarMatrix











Отзывы: