CleaverBrooks CBLE Скачать руководство пользователя | Manualshive

Страница: 119 / 194

background image

750-91 (revised 2009)
Model CB-LE Packaged Boiler Manual

7-3

7.1 — Overview

NO IGNITION

1.

Lack of spark.
A. Electrode grounded or porcelain cracked.
B. Improper electrode setting.
C. Loose terminal on ignition cable - or cable shorted.
D. Inoperative ignition transformer.
E. Insufficient or no voltage at pilot ignition circuit terminal.

2.

Spark but no flame.
A. lack of fuel - no gas pressure, closed valve, empty tank, broken line, etc.
B. Inoperative pilot solenoid.
C. Insufficient or no voltage at pilot ignition circuit terminal.
D. Too much air.

3.

Low-fire switch open in low-fire proving circuit.
A. Damper motor not closed, slipped cam, defective switch.
B. Damper jammed or linkage binding.

4.

Running interlock circuit not completed.
A. Combustion or atomizing air proving switches defective or not properly

set.

B. Motor starter interlock contact not closed.

5.

Flame detector defective, sight tube obstructed, or lens dirty.

PILOT FLAME, BUT NO
MAIN FLAMW

1.

Insufficient pilot flame.

2.

Gas fired unit:
A. Manual gas cock closed.
B. Main gas valve inoperative.
C. Gas pressure regulator inoperative.

3.

Oil fired unit:
A. Oil supply cut off by obstruction, closed valve, or loss of suction.
B. Supply pump inoperative.
C. No fuel.
D. Main oil valve inoperative.
E. Check oil nozzle, gun, and lines.

4.

Flame detector defective, sight tube obstructed or lens dirty.

5.

Insufficient or no voltage at main fuel valve circuit terminal.

BURNER STAYS IN LOW-
FIRE

1.

Pressure or temperature above modulating control setting.

2.

Manual-automatic switch in wrong position.

3.

Inoperative modulating motor.

4.

Defective modulating control.

5.

Binding or loose linkage, cams, setscrews, etc.

Problem

Possible Cause(s)

«
...
117
118
119
120
121
...
»

Содержание CBLE



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CBLE

LOGIC HEAT2 H12

Бренд: Ideal Heating Страницы: 8

LOGIC COMBI2 C24

Бренд: Ideal Heating Страницы: 10

Бренд: Radiant Страницы: 16

Aerco Modulex EXT Series

Бренд: Watts Страницы: 144

Luna Duo-Tec MP 1.35

Бренд: Baxi Страницы: 92

VOGUE MAX SYSTEM 32IE

Бренд: Ideal Heating Страницы: 80

Бренд: State Water Heaters Страницы: 20

ecoMAX pro 18 E

Бренд: Vaillant Страницы: 36

Бренд: Jaspi Страницы: 13

Burkay Genesis GB-1000

Бренд: A.O. Smith Страницы: 2

Бренд: PeerlessBoilers Страницы: 43

Бренд: Ravenheat Страницы: 54

Smart Green 130

Бренд: ACV Страницы: 24

HeatMaster 120 TC

Бренд: ACV Страницы: 62

WaterMaster 120 Evo

Бренд: ACV Страницы: 76

Бренд: Lochinvar Страницы: 48

InterSystem HE26

Бренд: Atmos Страницы: 56

Mod Con 300 VWH

Бренд: HTP Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды