ClearSpan Value Line 106178 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 23

ClearSpan Value Line 106178 Скачать руководство пользователя страница 7

7

CLEARSPAN

™

VALUE LINE

Revision date: 06.21.08

LAY OUT THE BUILDING SITE

After the site is prepared, identify the location of the shelter

corners helps to square the frame after it is assembled.

Taking these steps

before

assembling the shelter saves

time and ensures that the structure is positioned as

desired. The following procedure is a suggested method. Its

use depends on the size of the shelter, shelter application,

the footings, and the method used to anchor the shelter.

SQUARE THE SITE

1. Identify a corner where a building rafter will be

positioned, drive in a stake, and string a line the exact

width of the building and stake in place.

2. Sting a line at least as long as the building from the first

stake at 90°.

NOTE:

A transit can be used to ensure an accurate 90°

angle, or the 3-4-5 rule can be used. Refer to diagram.

Using multiples of 3-4-5 such as 6-8-10 or 12-16-20

helps to maintain an accurate 90° angle.

3. After squaring the position of the building and placing

a stake at all corners, string a line between the stakes

to mark the base of the building.

ASSEMBLING THE ROUND STYLE STORAGE MASTER

COMPONENTS
NOTE

: Assistance is required to assemble the shelter.

RAFTER ASSEMBLY

Gather the parts:
•  Rafter position #1 (Pipe #14R1601)
•  Rafter position #2 (Pipe #14R1602)
•  Rafter position #3 (Pipe #14R1603)
•  27" Leg extension (Pipe #166S027)
•  End clamps (#102856)
•  Band clamps (#QH1402)
•  Tek Screws
•  Nut setter 3/8" magnetic

Rafter Assembly Procedure:

Each rafter assembly consists of six (6) rafter sections:

two (2) curved rafter pipes (for the top), two (2) side pipes

that connect to the upper center pipes, and two (2) leg

extension pipes.
1. Select the six (6) pipes needed to assemble a rafter

and arrange these on a flat surface as shown below for

assembly.

2. Slide the swaged portion of each rafter pipe into the

plain end of the pipe as shown.

(#14R1602)

(#14R1603)

(#14R1601)

(#166S027)

«
...
5
6
7
8
9
...
»

Содержание Value Line 106178
























Отзывы:

Нет отзывов