manualshive.com logo in svg

ClearSpan Value Line 106178, Руководство по сборке

Поделиться
Скачать
ClearSpan Value Line 106178 Скачать руководство пользователя страница 4

CLEARSPAN

™

 VALUE LINE

4

Revision date: 06.21.08

REQUIRED TOOLS

The following list identifies the main tools needed to  

assemble the shelter. Additional tools and supports may be 

needed depending on the structure, location, and  

application.
•  Tape measure or measuring device
•  Variable speed drill and impact driver (cordless with 

extra batteries works best) 

•  Wrenches or ratchet and socket set (recommended)
•  1/4'' Allen wrench
•  Scissors or utility knife
•  Ropes long enough to reach over the shelter
•  Hammers, gloves, and eye protection
•  Metal file and metal cutting saw
•  Duct tape 
•  Ladders, work platforms, and other machinery for lifting  

designed to work safely at the height of the shelter

UNPACK AND IDENTIFY PARTS

The following steps will ensure that you have all the  

necessary parts before you begin to assemble the shelter.
1.  Unpack the contents of the shipment and place where  

you can easily inventory the parts. Refer to the Bill of  

Materials/Spec Sheets.

2.  Verify that all parts listed on the Bill of Materials/Spec  

Sheets are present. If anything is missing or you have  

questions, consult the Pictorial Parts Guide and all  

shelter diagrams for clarification, or contact Customer  

Service.

 

NOTE:

 At this time, you do not need to open the plastic  

 

bags containing smaller parts such as fasteners or  

 washers.

QUICK-START GUIDE

For a quick overview of this shelter and its components, 

consult the Quick-Start Guide at the back of these 

instructions.

Space below is reserved for customer notes.

Содержание Value Line 106178
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды