ClearSpan 106772 Скачать руководство пользователя страница 12

Страница: 12 / 53

CLEARSPAN

™

JOB MASTER BUILDINGS

Revision date: 07.23.09

ASSEMBLE OUTRIGGER RAFTERS

Each outrigger rafter consists of two (2) large 2" x 3"

rectangular pipes and a pipe strap.

Gather the parts:
•  Rafter pipe ( #R23S075)
•  Rafter pipe (#07CPR23P1)
•  Pipe strap (#QH1070)
•  Tek screws and magnetic nut setter (3/8'' x 2-9/16")

The following steps describe one way to assemble the

individual rafters. Consult the Front Profile rafter diagram in

the Quick Start section to view an assembled rafter.

1. Position the 2" x 3" rectangular tubes as shown.

2. Insert the swaged end of the curved pipe into the

plain end of the straight pipe to assemble the rafter as

shown.

Typical Outrigger Rafter Assembly

#R23S075

#07CPR23P1

3. After connecting the separate pipes, locate one (1) pipe

strap (#QH1070) and install as shown.

ATTENTION:

The pipe strap is installed on the

underside of the rafter with one Tek screw on each side

of the pipe splice as shown.

4. Install two additional Tek screws at each pipe joint in

the location identified above.

NOTE:

DO NOT TIGHTEN THE PIPE STRAP AT THIS

TIME. The pipe strap will be tightened after the purlin is

installed.

5. Repeat the procedures to assemble the remaining

rafters.

6. After all rafters are assembled, assemble the outrigger

base rail assemblies.

Tek screws

Содержание 106772






















































Результаты поиска

Содержание 106772

Отзывы:

Бренды по названию

Популярные бренды

ClearSpan 106772, Руководство пользователя

Результаты поиска

Содержание 106772

Отзывы:

Бренды по названию

Популярные бренды