background image

5900e Greensand Filter Installation & Startup Guide 

Page 3 

www.cleanwaterstore.com 

Rev 082216 

 

 

Potassium Permanganate Tank with Float ............................................................................................. 18 

Permanganate Tank Not Filling With Permanganate Solution ............................................................... 18 

How To Remove Media From Control Head ........................................................................................... 19 

More Troubleshooting Tips: .................................................................................................................... 20 

Service Instructions: ................................................................................................................................ 21 

Replacing The Brine Valve, Injectors, and Screen ................................................................................... 21 

 

Packing List 

Greensand Filter 0.75 cubic foot size 

5900e Plus Backwash Control Valve w/ Bypass Assembly and Pipe connector kit (1”or ¾”) 
8” x 44” filter tank with distributor tube 
Blue media funnel for adding the Greensand media 
8 lbs. Filter gravel  
0.75 cubic foot of Greensand media 

Greensand Filter 1.0 cubic foot size 

5900e Plus Backwash Control Valve w/ Bypass Assembly and Pipe connector kit (1”or ¾”) 
9” x 48” filter tank with distributor tube 
Blue media funnel for adding the Greensand media 
12lbs. Filter gravel  
1 cubic foot of Greensand media 

Greensand Filter 1.5 cubic foot size 

5900e Backwash Control Valve w/ Bypass Assembly and Pipe connector kit (1”or ¾”) 

10” x 54” filter tank with distributor tube 

Blue media funnel for adding the Greensand media 

16 lbs. Filter gravel  

1.5 cubic feet of Greensand media 

Greensand Filter 2.0 cubic foot size  

5900e Backwash Control Valve w/ Bypass Assembly and Pipe connector kit (1”or ¾”) 

12” x 52” filter tank with distributor tube 

Blue media funnel for adding the Greensand media 

20 lbs. Filter gravel  

2.0 cubic feet of Greensand media 

Содержание Tannin 5900e Series























Отзывы: