Clean Water Systems Tannin 5900e Series Скачать руководство пользователя | Manualshive

Страница: 20 / 22

background image

5900e Greensand Filter Installation & Startup Guide

Page 20

www.cleanwaterstore.com

Rev 082216

More Troubleshooting Tips:

PROBLEM / SYMPTOM

POSSIBLE CAUSE

SOLUTION

Iron or manganese or sulfur
odor in treated water after
Greensand Filter

No permanganate in solution
tank

Not backwashing often
enough

Water being used when
Greensand Filter is in
regeneration.

Permanganate solution is not
being sucked in during the
regeneration brine cycle.

Greensand media exhausted

Add permanganate powder to tank and
regenerate greensand filter

Set to backwash more frequently.
Backwash twice in one day and re-check
water.

If any water is used during the 90 minute
regeneration cycle, untreated water will
enter household piping. Set time
Greensand Filter regenerates to a time
when no one will be using the water.

Clean brine injector

Clean potassium permanganate tank

Replace permanganate support pad in
permanganate tank

Inadequate backwash flow. Make sure
there that Greensand Filter is backwashing
at the correct backwash flow rate (5 to 10
gallons per minute depending on size of
filter).

Low water pressure. Increase water
pressure to unit by adjusting well pump
pressure switch, or replacing well pump.

Replace Greensand media with new
Greensand.

«
...
18
19
20
21
22
»

Содержание Tannin 5900e Series























Отзывы:

Нет отзывов

Похожие инструкции для Tannin 5900e Series

Бренд: Nelson Страницы: 12

Бренд: Hunter Страницы: 2

Бренд: Aqua Flo Страницы: 4

ProfiClear Premium XL Moving Bed Modul

Бренд: Oase Страницы: 105

Softcontrol Data/F

Бренд: Ofs Страницы: 46

Бренд: Eaton Страницы: 9

Бренд: Bluewater Страницы: 100

Бренд: Netafim Страницы: 2

Бренд: Netafim Страницы: 16

Бренд: Netafim Страницы: 14

Бренд: Morphy Richards Страницы: 6

Бренд: IMI NORGREN Страницы: 5

Бренд: DeVilbiss Страницы: 12

Бренд: HYDAC FILTER SYSTEMS Страницы: 80

Бренд: LUBMANN Страницы: 16

Бренд: Hydac Страницы: 36

EDGE infinity MRC1882A-600G

Бренд: Schoner Wassertechnik Страницы: 42

Schwefelnitratreductor SN Blue

Бренд: Aqua Medic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды