manualshive.com logo in svg

Clean Water Systems Pro-OX 5700-E, Инструкция по установке и запуску, Страница: 5 / 30

Поделиться
Скачать
Clean Water Systems Pro-OX 5700-E Скачать руководство пользователя страница 5

5700-E Softener Installation & Startup Guide 

Page 4

 

www.cleanwaterstore.com 

Rev 091514 

Pre-Installation 

 

1.

 

Review your packing list and make sure you have received all the parts before beginning installation.  
Please ensure that all parts are included before scheduling a plumber or installer to come to the site. 

2.

 

If you are going to be turning off the water to the house and you have an electric water heater, shut 
off the power to the water heater before beginning installation in case water heater is accidentally 
drained. 

3.

 

Pick a suitable location for your filter system on a dry level spot where it won’t be exposed to freezing 
temperatures.   A minimum of 20 PSI is required.  Maximum pressure is 90 PSI. 

4.

 

Get all of your plumbing parts together before beginning installation.  Installation typically takes 3 to 
5 hours.  However after installation the Softener must be allowed to run through a complete 
backwash and rinse cycle (also called ‘regeneration’).   You don’t have to be present for this first 
backwash necessarily, but it does take 90 minutes. 

5.

 

After the system is installed and running, your water may be discolored, or full of sediment/rust, 
particularly if this is older piping that has been exposed to iron or manganese for some time.  
Typically this clears up over a day or two, but can persist for weeks if the pipe is old galvanized iron 
pipe that is corroded. 

 

Best Practices for Piping & Drain Installation 

 

1.

 

See typical installation (see Fig 2).   The softener is installed after the pressure tank. 

2.

 

Make sure to connect the IN pipe to the 5700-E inlet and the OUT to the outlet (see Fig 3). As you 
face the 5700-E control from the front, the water enters on the right and exits on the left.  From the 
back (see Fig 3) the water enters on the left and exits on the right.  The inlet and outlet are attached 
to the bypass valve which is marked with arrows as well. 

3.

 

Make sure there is a working gate or ball valve before the 5700-E Softener and also one after as 
shown in the diagram (Fig 2). The pressure gauges are optional but a hose bib (a faucet that you can 
attach a garden hose to) is strongly recommended after the softener and before the second ball 
valve.  This makes it easy to rinse your new softener on start-up and gives you a place to test the 
water before it enters your household plumbing. 

4.

 

If you will be using copper piping, do not sweat the copper pipe directly on to the 5700-E control 
valve.  Avoid heating up the 5700-E control valve plastic with the torch. 

Содержание Pro-OX 5700-E































Отзывы:

Нет отзывов