background image

The two horizontal mounting bars [1] mount 

to the handlebars of your machine with a 
U-clamp system designed to fit a variety of 
different machines. 

The bars must be mounted on your machine 

in a way that will not interfere with its 
operation, controls, lights or moving parts.

The preferred mounting location for the 

horizontal mounting bars is on the front (motor 
side) of the handlebars. However you may 
need to mount one or both bars on the back 
of the handlebar. 

Please see the following page for diagrams 

of other mounting options.

Find the four 3/4" U-Clamps [4J] and put 

one clamp on each end of the two horizontal 
mounting bars [1].

Now test the larger U-clamps [4AA, 4BB, 4CC 

or 4DD] to see what clamp fits snugly around 
the handlebars of your snow thrower.

Determine where the lower mounting bar 

should be on your machine (you will install the 
upper one later). It should be placed on the 
handlebars a minimum of 17" and a maximum 
of 24" from the ground (as measured from the 

center of the holes in the 
bar end). This will allow 
headroom of at least 6.5' 
in the peak of the cab 
roof. 

Using 5/16" x 2-3/4" [D] 

or 3-1/4" [E] bolts, bolt the 
horizontal mounting bar 
U-clamps to the handlebar 
U-clamps as shown above.

Thread a lock nut [F] on 

the bolt ends just enough to hold the parts 
in place. 

The lock nuts have a vibration resistant 

lining and will be stiff to put on. There is 
nothing wrong with the threading.

Level the horizontal mounting bar and 

center it over the handlebars then 
SNUG DOWN ALL OF THE BOLTS.

NOTE: On some snow throwers the entire 

cab must be offset to one side to clear the 
machine controls. You can offset the cab or 
increase the headroom later by moving the 
mounting bars to one side or raising them 
higher on the handlebars.

7

1

4 J

4AA, 
4BB, 4CC 
or 4DD

4AA, 4BB, 
4CC or 4DD

Step 3:  Install the lower horizontal mounting bar

  

IMPORTANT: The proper placement of this piece 

   

is critical to the rest of the installation. 

17-24"

4 J

Содержание Deluxe Snow Thrower Cab















Отзывы: