background image

Your snow thrower must be OFF 

and COOL before you install your 

cab.

TOOLS NEEDED:

• One tape measure
• One 10" adjustable wrench 
Either (your choice)
• One 7/16" wrench or socket and one 

1/2" wrench or socket or 

• Another adjustable wrench

  (You may find it easier to use at least 

one socket wrench for leverage as the 
lock nuts are designed to fit tightly)

• 13 – 15 lbs. of sand or non-clumping 

 cat litter

Step 1: Assemble the sand bag

Lay the empty counterweight sand bag [6] 

down as shown. 

Insert one end of the sand bag bracket [7] 

rod into one of the small pockets by the snap 
tab.

Grasp the clamp where it fits in the pocket 

then pull the opposite unfilled pocket out until 
you can slip it onto the other end of the rod. 
(The bag will stretch to allow the rod to slip 
into the pocket.)

Fasten the snap tab around the rod between 

the clamps.

Fill the sand bag with a minimum of 13 

pounds of dry sand or non-clumping cat litter.

Step 2: Install the sand bag

Start two 5/16" x 1-1/4" capscrews [H] into 

the sand bag mounting bracket clamps [7]. 
Don't screw the capscrews all the way in.

Close the bag by rolling the opening rod 

towards the sand bag then up and under the 
sand bag mounting brackets.

Now put the sand bag counterweight and 

its bracket on top of the auger housing.

The counterweight sand bag should lay 

towards the BACK side of the auger housing. 
Do not cover any warning labels. 

Hold the ends of both the mounting bracket 

rod and the closing rod and place the bag on 
top of the auger housing as shown above. 
Slide the bag over the top of the auger 
housing until the front edge of the housing 
meets the inside edge of the mounting 
brackets. Tighten the bracket capscrews to 
SECURELY hold the counterweight to the auger 
housing. 

It's a good idea to check the capscrews 

for tightness before each use of machine.

6

Installation Instructions

6

7

Содержание Deluxe Snow Thrower Cab















Отзывы: