Clarke IG1000 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

background image

19

THE AIR FILTER (EVERY 50 HOURS OF USE)

1. Remove the left side maintenance panel.

2. Remove the air filter cover screw

shown on the right.

3. Remove the air filter cover.

4. Remove the air filter element.

5. If the air filter is damaged contact

Clarke spare parts department for
a replacement See page 2.

• If the filter is dirty, wash the filter

in a solution of warm water and
mild detergent and rinse
thoroughly. Leave the filter to
dry completely, once it is dry
immerse the filter in clean
engine oil and sqeeze the filter to remove excess oil.

6. Replace the filter back into its original position and replace the air filter

cover.

WARNING: DO NOT USE FLAMMABLE SOLVENTS OR PETROL TO CLEAN THE
AIR FILTER.

«
...
17
18
19
20
21
...
»

Содержание IG1000





























Отзывы:

Нет отзывов

Похожие инструкции для IG1000

VLT DeviceNet MCA 104

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 138

Бренд: Danfoss Страницы: 108

Бренд: Danfoss Страницы: 140

Бренд: Danfoss Страницы: 149

IMP-C1000-SFP-bt-24 Series

Бренд: ANTAIRA Страницы: 2

Бренд: Prism Sound Страницы: 63

Бренд: Qoltec Страницы: 12

Бренд: Pixelfly Страницы: 12

Бренд: Tripp Lite Страницы: 24

Бренд: Phaesun Страницы: 2

NX Distributed Intelligence NX MEDIA CONVERTER

Бренд: Hubbell Страницы: 3

Бренд: Midian Electronics Страницы: 4

Бренд: DAYLIFF Страницы: 12

Бренд: Raider Страницы: 108

Бренд: Powerlink Страницы: 4

Бренд: Crystal Vision Страницы: 70

TECHNOLOGY TIG 172

Бренд: Telwin Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды