Clarke Contractor CON1500RDV Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

background image

14

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE AND SERVICING

BEFORE USE

1. Ensure all fixing screws remain tight to ensure the drill is in safe working

condition.

2. Inspect the power cable to ensure it is free from cracks, bare wires etc.

CLEANING

1. Ensure all air ventilation slots are clear of blockages, (use compressed air to

clean the machine if possible).

2. After use, clean all dust and swarf from the drill.

3. Clean the exterior of the drill with a soft cleaning cloth. Never use any

chemicals or harsh abrasives to clean the tool.

• Avoid using solvents when cleaning plastic parts; most plastics are

susceptible to damage from various types of commercial solvents.

GEARBOX GREASE

After extensive use, grease may be added to the hammer drill mechanism via
the grease port cover.

1. Remove the grease port cover

using the wrench supplied.

2. Apply sufficient grease to cover

all visible moving parts

• DO NOT overfill the gearbox.

3. Replace the grease port cover

and hex bolts before using the drill
again.

• All other bearings etc, in this

tool are lubricated with sufficient high grade lubricant for the tools
lifetime under normal operating conditions, therefore no further
lubrication is necessary.

• There are no other user serviceable parts in this machine. Refer to your

CLARKE dealer if internal maintenance is required.

WARNING: MAKE SURE THAT THE DRILL IS SWITCHED OFF AND
DISCONNECTED FROM THE MAINS SUPPLY BEFORE STARTING ANY
CLEANING OR MAINTENANCE PROCEDURES.

«
...
12
13
14
15
16
...
»

Содержание Contractor CON1500RDV





















Отзывы:

Нет отзывов

Похожие инструкции для Contractor CON1500RDV

Бренд: Kay Home Products Страницы: 3

Бренд: Makita Страницы: 16

Бренд: Berner Страницы: 149

Бренд: Steba Страницы: 12

Бренд: Uniflame Страницы: 24

Бренд: P.I.T. Страницы: 21

SALAMANDER 688.003

Бренд: CaterChef Страницы: 5

Бренд: Camp Chef Страницы: 2

Бренд: Fire Sense Страницы: 3

Бренд: Weber Страницы: 36

SMOKEPRO PG24-3

Бренд: Camp Chef Страницы: 14

GALAXY BQ1190BLB

Бренд: Gasmate Страницы: 24

Бренд: garbou Страницы: 24

Бренд: OUTDOOR CHEF Страницы: 2

ELEKTROGRILL ODESSA

Бренд: tepro Страницы: 84

Бренд: Blue Seal Страницы: 18

Бренд: Hilti Страницы: 60

Бренд: BTI Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды