Weber 1000 LX Series Скачать руководство пользователя

Страница: 1 / 36

Serial Number

Please use this number in registering your warranty and
any correspondence with the factory.

Owner’s Manual

WARNING: Do not try to light this appliance
without reading "Lighting" instructions
section of this manual.

THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.

NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.

FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your

gas supplier or your fire department.

FOR YOUR SAFETY
1. Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

2. An LP tank not connected for use shall

not be stored in the vicinity of this or
any other appliance.

WARNING: Follow all leak check procedures
carefully in this manual prior to barbecue
operation. Do this even if barbecue was
dealer assembled.

National

Association

PROPANEGAS

98640

12/97

GENESIS

1000 LX Series

LP Gas Barbecue

Содержание 1000 LX Series





































Результаты поиска

Содержание 1000 LX Series

Отзывы:

Похожие инструкции для 1000 LX Series

Бренды по названию

Популярные бренды

Weber 1000 LX Series, Руководство пользователя

Результаты поиска

Содержание 1000 LX Series

Отзывы:

Похожие инструкции для 1000 LX Series

Бренды по названию

Популярные бренды