background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY PRECAUTIONS

1) WORK AREA SAFETY 

a.

Keep work area clean and well lit. 

Cluttered or dark areas invite accidents.

 

b.

Do not operate power tools in explosive atmospheres, such as in the presence of 
flammable liquids, gases or dust.

 

Power tools create sparks which may ignite the 

dust or fumes. 

c.

Keep children and bystanders away while operating a power tool.

 

Distractions 

can cause you to lose control. 

2) ELECTRICAL SAFETY 

a.

Power tool plugs must match the outlet. Never modify the plug in any way. Do 
not use any adapter plugs with earthed (grounded) power tools.

 

Unmodified 

plugs and matching outlets will reduce risk of electric shock. 

b.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, 
ranges and refrigerators. 

There is an increased risk of electric shock if your body is 

earthed or grounded. 

c.

Do not expose power tools to rain or wet conditions.

 

Water entering a power tool 

will increase the risk of electric shock. 

d.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the 
power tool. Keep cord away from heat, oil, sharp edges or moving parts.

 

Damaged or entangled cords increase the risk of electric shock. 

e.

When operating a power tool outdoors, use an extension cord suitable for 
outdoor use. 

Use of a cord suitable for outdoor use reduces the risk of electric 

shock. 

f.

If operating a power tool in a damp location is unavoidable, use a residual 
current device (RCD) protected supply.

 

Use of an RCD reduces the risk of electric 

shock. 

3) PERSONAL SAFETY 

a.

Stay alert, watch what you are doing and use common sense when operating a 
power tool. Do not use a power tool while you are tired or under the influence of 
drugs, alcohol or medication

A moment of inattention while operating power 

tools may result in serious personal injury. 

b.

Use personal protective equipment. Always wear eye protection.

 

Protective 

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing 
protection used for appropriate conditions will reduce personal injuries. 

WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL 
INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/
OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED 
BELOW REFERS TO YOUR CORDLESS MULTI FUNCTION TOOL AN

CHARGER.

Содержание CMFTLi

















Отзывы: