background image

2

INTRODUCTION

Thank you for purchasing this Clarke siphon feed sandblaster.

Before you try to use this product, read this manual and follow the instructions 
carefully. In doing so you will ensure your safety and the safety of others 
around you. You can also look forward to a purchase that gives you long and 
satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 
months from the date of purchase. Please keep your receipt which will be 
required as proof of purchase. 

This guarantee is invalid if the product is found to have been abused or 
tampered with in any way, or not used for the purpose for which it was 
intended.

Faulty goods should be returned to their place of purchase, no product can 
be returned to us without prior permission. 

This guarantee does not effect your statutory rights.

CONSUMABLES

Please be aware that certain parts of this sandblaster will wear, requiring 
replacement and that these parts may not be covered by your guarantee.

The wear on certain parts depends on the abrasiveness of the materials used. 

Replacement parts are available from your nearest Clarke International 
dealer.

Содержание 7640117













Отзывы: